background image

   

TC-9 Viper ™ Gate System 

Residential Sliding Gate Operator 

 

23 

Limited Warranty 

 

You must read, understand and agree with items in the Limited 

Warranty. 

 

GATEMOTORS INC. Warrants the 

Sliding Gate Operator to be free of 

defects in workmanship and materials for a period of 1 year for electronics, mechanical 
components and chassis for perforation due to corrosion and 2 year warranty on motor. 
 
GATEMOTORS INC reserves the right of final determination as to the existence and 
causes of any defect or failure. Any part or parts found to be defective and are returned to 
GATEMOTORS INC within the warranty period, shall at our option be repaired or 
replaced free of charge F.O.B. the factory. 
 
The warranty will not apply the following circumstances, which are considered beyond 
our control. Mis-use, vandalism, accident, neglect, unauthorized repairs or modifications, 
acts of God (lightning, floods, insect damage, etc..), power surges, units subjected to 
corrosive environments, incorrect installation or application, damage to mechanism due 
to wrong type of gate, incorrect weight, gate not operating freely or not on level ground. 
 
The warranty set forth above is entirely exclusive and no other warranty whether written 
or oral, is expressed or implied. GATEMOTORS INC. specifically disclaims any and all 
implied warranties, merchantability or fitness for a particular purpose. It is the  
purchaser’s sole and exclusive responsibility to determine whether or not the equipment 
will be suitable for a particular purpose. In no event shall GATEMOTORS INC. be held 
liable for direct, indirect, incidental, special, consequential damages or loss of profits 
whether based on contract, tort, or any other legal theory during the course of the 
warranty or at any time there after. The installer and/or end user do agree to assume all 
responsibility for all liability in use of this product, releasing GATEMOTORS INC. of all 
liability.

 

IN ORDER TO INSTALL AND USE THE

 SLIDING GATE 

OPERATOR, YOU MUST UNDERSTAND AND BE IN FULL UNCONDITIONAL 
AGREEMENT WITH ALL STIPULATIONS OUTLINED ABOVE. IF YOU ARE 
NOT IN FULL AGREEMENT, DO NOT PUT UNIT INTO OPERATION. IF 
OPERATOR IS PUT INTO OPERATION THIS WILL BE CONFIRMATION 
THAT YOU ARE IN FULL UNCONDITIONALL AGREEMENT WITH ALL OF 
THE ABOVE STIPULATIONS.

 

 

25

Summary of Contents for TC-9

























Reviews: