LIGHTING INSTRUCTIONS GRILL/ROTIS
WARNING: IMPORTANT!
BEFORE LIGHTING…
Inspect the gas supply piping or hose prior to turning the
gas “ON”. If there is evidence of cuts, wear, or abrasion,
it must be replaced prior to use. Do not use the grill if the
odor of gas is present. The pressure regulator and hose
assembly supplied with the unit must be used. Never
substitute regulators for those supplied with the grill. If a
replacement is necessary, contact the factory for proper
replacement.
Screw the regulator (type QCC1) onto the tank. Leak
check the hose and regulator connections with a soap and
water solution before operating the grill (see assembly
instruction).
TO LIGHT THE GRILL BURNER:
Turn all knobs to “OFF” then turn on the gas supply.
Always keep your face and body as far from the grill as
possible when lighting.
Open the lid, push and turn one control knob to the “HI”
position and press the electric igniter for 3 to 4 seconds
to light the burner. If the burner does not light, wait for 5
minutes then retry.
TO MATCH LIGHT THE GRILL:
If the burner will not light after several attempts then the
burner can be match lit.
If you’ve just attempted to light the burner with the
igniter, allow 5 minutes for any accumulated gas to
dissipate. Keep your face and hands as far away from the
grill as possible. Insert a lit extended match or lighter
through the cooking grids to the burner. Press the control
knob and rotate left to the HI setting which should
release the gas. Burner will light immediately.
Push and turn the control knob which is centered on the
burner to “HI”. If the burner does not light in 4 seconds
turn the knob off, wait 5 minutes and try again.
TO LIGHT THE ROTIS BURNER:
Open the lid, push and turn the control knob to the “HI”
position. Press the electric igniter for 3 to 4 seconds to
light the burner. If the burner does not light within 4
seconds, turn the control knob to “OFF”. If the igniter
does not function, the burner can be lit by holding a lit
match to the burner (with the control knob at “HI”).
Keep a spray bottle of soapy water near the gas supply
valve and check the connections before each use.
Do not attempt to light the grill if odor of gas is present.
Call for service 1-800-913-8999.
USING THE SIDE BURNER
WARNING: IMPORTANT!
USING THE SIDE BURNER:
Inspect the gas supply piping or hose prior to turning the
gas “ON”. If there is evidence of cuts, wear or abrasion,
it must be replaced prior to use. Do not use the side
burner if the odor of gas is present.
WARNING: Always keep your face and body as far
away from the burner as possible when lighting.
LIGHTING INSTRUCTIONS
To light side burner, remove any cooking utensils from
the burner grate. Push and turn the control knob
counterclockwise to the “HI” position. This will start the
gas flowing. Press the electric igniter for 3 to 4 seconds
to light the burner. If the burner does not light within 4
seconds, turn the control knob to “OFF”. If the smell of
gas is detected and the igniter is not functioning,
immediately turn the control knob “OFF”. Allow 5
minutes for any accumulated gas to dissipate, then see
the following section for “MATCH LIGHTING”.
MATCH LIGHTING
Hold a lit extended match or lighter near the burner
ports, turn the control knob counterclockwise to “HI”.
Move your hand immediately once the burner is lit.
Rotate the control knob to the desired setting. Check for
proper burner flame characteristics. Each burner is
adjusted prior to shipment; however, variations in the
local gas supply may take minor adjustments necessary.
Burner flames should be blue and stable with no yellow
tips, excessive noise, or lifting. If any of these conditions
exist call our customer service line. If the flame is
yellow, it indicates insufficient air. If the flame is noisy
and tends to lift away from the burner, it indicates too
much air.
STAINLESS STEEL
The grill is made from non-rusting and non-magnetic
stainless steel. There are many different stainless steel
cleaners available. Always use the mildest cleaning
13
