background image

 

BORIS Operating Manual  

Page 4 

2.

 

INSTALLATION INSTRUCTIONS 

2.1

 

General Description 

BORIS is a fast transfer line-interactive uninterruptible power supply.  It is designed to 

prevent blackouts, brownouts, sags, swells and surges from reaching the protected load 

under normal conditions.  It filters out small utility line fluctuations and isolates the 

protected load from large disturbances by internally disconnecting from the utility line, while 

supplying power from its internal batteries until the utility line returns to normal.    

While operating on battery, an internal alarm will intermittently beep.  The ON/TEST 

button may be pressed to silence the alarm.  If the line utility does not return and the 

battery continues to power the protected load, a low battery shutdown may occur.  Advance 

warning of a low battery condition begins approximately two minutes before the final 

shutdown.  This alarm will be a continuous beeping sound and cannot be silenced.  When 

used with a Virginia Controls controller, this condition should not occur (if batteries were 

previously charged fully) since the controller utilizes the remote shutdown capability of 

BORIS.   

Special features include surge protection; EMI/RFI filtering, high and low voltage 

correction (without draining batteries), as well as automatic battery testing during power up 

and every 14 days thereafter.  User-replaceable batteries can be replaced without having to 

remove power from the loads. 

2.2

 

Location Factors 

BORIS is intended for use in a protected environment.  Avoid locations where 

temperatures exceed 40°C (104°F) or fall below 0°C (32°F) as it will shorten battery life 

and discharge time respectively.  Do not locate BORIS in an environment, which may 

contain excessive dust, dirt, chemicals, toxic gases, etc.  Do not block vents located on the 

sides of the unit. 

2.3

 

Storage 

If it is desired to store BORIS for an extended period, an optional power cord is available 

which enables the batteries to be charged by connecting the unit directly to a wall outlet 

(120 VAC).  Batteries should be charged for 3 hours every 6 months.  Repeat every 3 

months in hot locations.  Store in a cool, dry environment below 29.4°C (85°F). 

Summary of Contents for BORIS 1000VA


















Reviews: