virtual access GW8600 Service Managed Gateway Installing And Configuring Download

Page: 3 / 12

About this document

Installing and Configuring the GW8600 SMG

Issue 1.1

Page 3 of 12

About this document

1.1

Scope

This document explains how to:

•

physically install the GW8600 Service Managed Gateway (SMG), and

•

set up the WebWayOne 2424B Communicator for GPRS through HyperTerminal.

This document does not explain in detail how to use the web interfaces to configure the
SMG or WebWayOne 2424B Communicator.

1.2

Readership

This document is for network engineers.

1.3

More information

For more information about WebWayOne 2424B Communicator, read the WebWayOne
document,

Getting Started With Your WebWayOne 2424B Communicator

1.4

Terminology

ARC

Alarm receiving centre

PSU

Power supply unit

SMG

Service Managed Gateway

WWO

WebWayOne

Summary of Contents for GW8600 Service Managed Gateway













Search results

Summary of Contents for GW8600 Service Managed Gateway

Reviews:

Related manuals for GW8600 Service Managed Gateway

Brands by name

Popular brands

virtual access GW8600 Service Managed Gateway, Installing And Configuring

Search results

Summary of Contents for GW8600 Service Managed Gateway

Reviews:

Related manuals for GW8600 Service Managed Gateway

Brands by name

Popular brands