15
angle trimmer on the rail in this position by tightening
knob P1 (Fig. 12) and with the tool at the bottom of
the back rim.
- For greater safety, you should also use a suction pad
to fasten the other side of the angle trimmer base to
the work top, as explained in section 9.5 FASTENING
THE MACHINE TO THE PART.
- Slowly cut the rim in an upwards direction with the
assistance of the rising force of the shock absorber.
11. MAINTAINING THE BRUSHES
AND COLLECTOR
Make sure the machine is disconnected
from the power supply before performing
any maintenance work.
The brushes must be replaced when they have a minimum
length of 5 mm. Remove the covers F2 that hold the
brushes G2 (Fig. 20) and replace them with VIRUTEX
originals, making sure they slide smoothly inside the
guides. Remove the brush inside the switch box by
loosening the screws H2 (Fig. 20) that hold the box and
the switch I2 in position to reveal the cover F2 (Fig. 20).
Allow the machine to operate without load for a few
minutes after changing the brushes. Take advantage of
the brush change to check the condition of the collector.
If it appears burnt or has burrs it should be repaired by
the VIRUTEX repair service.
12. LUBRICATION AND CLEANING
The machine is factory delivered fully lubricated and
needs no special care throughout its working life. It is
important to carefully clean the machine after use with
a jet of dry air. Keep the power cable in good condition.
13. OPTIONAL ACCESSORIES
The following accessories are optional:
6027103 Chuck collet Ø 12
6027106 Chuck collet Ø
½
”
6022391 Reducer 12 to 10
6022387 Reducer 12 to 8
6022388 Reducer 12 to 6
6022389 Reducer 1/2” to 3/8”
6022390 Reducer 1/2” to 1/4”
1746245 Dust collector tube, length 5 m
6045673 Template for trimming ellipses and circles
Range of bits for corian and solid surface materials.
Guide rings:
7722168 D. ext. 10 for bits Ø up to 6
7722120 D. ext. 12 for bits Ø up to 8
7722121 D. ext. 14 for bits Ø up to 10
7722122 D. ext. 16 for bits Ø up to 12
7722169 D. ext. 18 for bits Ø up to 14
7722118 D. ext. 20 for bits Ø up to 16
7722119 D. ext. 27 for bits Ø up to 23
7722114 D. ext. 30 for bits Ø up to 26
1745838 UF317S Cutting guide with suction cups and
clamps.
9045754 Complete rail, length 1.40 m
9045755 Complete rail, length 2.40 m
6045756 Suction cup (set of 2)
6045710 Set of 2 clamps
9045812 Jointing kit for cutting guide
6046397 Dual square accessory
6045669 Guide accessory for circular cutting
6045715 UC60 Universal guide accessory for circular
cutting
5000000 PL11 Dovetail attachment
6045702 PFE60 Template for trimming work tops
6640125 Bit for AGB fittings
1745927 ASU317S Joining clamp
1745928 ATU317S Joining straps
14. NOISE AND VIBRATION LEVEL
The noise and vibration levels of this device have been
measured in accordance with European standard EN
60745-2-17 and EN 60745-1 and serve as a basis for com-
parison with other machines with similar applications.
The indicated vibration level has been determined for
the device’s main applications and may be used as an
initial value for evaluating the risk presented by expo-
sure to vibrations. However, vibrations may reach levels
that are quite different from the declared value under
other application conditions, with other tools or with
insufficient maintenance of the electrical device or its
accessories, reaching a much higher value as a result
of the work cycle or the manner in which the electrical
device is used.
Therefore, it is necessary to establish safety measures
to protect the user from the effects of vibrations, such
as maintaining both the device and its tools in perfect
condition and organising the duration of work cycles
(such as operating times when the machine is subjected
to loads, and operating times when working with no-load,
in effect, not in use, as reducing the latter may have a
considerable effect upon the overall exposure value).
15. WARRANTY
All VIRUTEX power tools are guaranteed for 12 months
from the date of purchase, exlcuding any domage which
is a result of incorrect use or of natural wear and tear
on the machine. All repairs should be carried out by the
official VIRUTEX technical assistance service.
16. RECYCLING ELECTRICAL EQUIPMENT
Never dispose of electrical equipment with domestic was-
Summary of Contents for FRE317S
Page 54: ...54 Fig 1 Fig 2 F E X U J D T B1 B C A Y1 F E Y1 B2 J2...
Page 55: ...55 Fig 4 Fig 3 E G I H J Q S O A P R W B2 C C2 D2 B M K L N...
Page 56: ...56 Fig 5 Fig 6 E3 E3...
Page 58: ...58 Fig 13 S1 T1 N1 U1 O1 Fig 14 Fig 15 Fig 16 O1 V1 U1 W1 X1 Fig 17 U1 T1 T1 U1 Fig 18...
