background image

1717 W Civic Drive, Milwaukee, WI 53209

414-354-6600

Design Modification Rights Reserved

© 2018 Visa Lighting

When using electrical equipment, basic safety precautions should always be followed, including the following:

•Read all instructions carefully before installing and save for future use.

•Make sure all connections are in accordance with the National Electrical Code and local regulations.

•To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture

•Service should be performed by qualified personnel.

•These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.

!

Model: CV2424
 

Linesse Linear Slot

Publication: 762302XX
Document Description:  Installation Instructions  
 

for 3” Linesse Linear Recessed  

 

Series Luminaires

7

CORNER INSTALLATION INSTRUCTIONS 

Horizontal Drywall Corner

Vertical IN Corner

Horizontal Grid Corner

23-1/2”

Flange Corner

Trimless/Flangeless Corner

Flange Corner

Flange Corner

Trimless/Flangeless Corner

Trimless/Flangeless Corner

Grid Corner

23”

Lens Area

20”

23”

20”

Lens Area

23”

Summary of Contents for Linesse CV2424











Reviews: