VISIOMED BewellConnect BW-PFX1, User Manual

BewellConnect - BW-PFX1 - User Manual - 072017v1

BewellConnect - BW-PFX1 - User Manual - 072017v1

68

69

EMC data

1.  This product needs special precautions regarding EMC and needs to be installed and 

put into service according to the EMC information provided, and this unit can be af-

fected by portable and mobile RF communications equipment.

2.  Do not use a mobile phone or other devices that emit electromagnetic fields, near the 

unit. This may result in incorrect operation of the unit.

3.  Caution: This unit has been thoroughly tested and inspected to assure proper perfor-

mance and operation!

4.  Caution: this machine should not be used adjacent to or stacked with other equipment 

and that if adjacent or stacked use is necessary, this machine should be observed to 

verify normal operation in the configuration in which it will be used.

Refer to further guidance below regarding the EMC environment in which the device 

should be used.

GUIDANCE AND MANUFACTURE’S DECLARATION – ELECTROMAGNETIC EMISSION

The BW-PFX1 is intended for use in the electromagnetic environment specified below. The customer of 

the user of the BW-PFX1 should assure that it is used in such an environment.

Emission test

Compliance

Electromagnetic environment - guidance

RF emissions

CISPR 11

Group 1

The BW-PFX1 use RF energy only for its internal function.

Therefore, its RF emissions are very low and are not

likely to cause any interference in nearby electronic

equipment.

RF emission

CISPR 11

Class B

The BW-PFX1 is suitable for use in all establishments,

including domestic establishments and those directly

connected to the public low-voltage power supply

network that supplies buildings used for domestic

purposes.

Harmonic emissions

IEC 61000-3-2

Class A

Voltage fluctuations/

flicker emissions

IEC 61000-3-3

Complies

GUIDANCE AND MANUFACTURE’S DECLARATION – ELECTROMAGNETIC IMMUNITY

The BW-PFX1 is intended for use in the electromagnetic environment specified below. The customer or 

the user of BW-PFX1 should assure that it is used in such an environment.

Immunity test

EN 60601  

test level

Compliance 

level

Electromagnetic environment -

guidance

Electrostatic 

discharge (ESD) 

IEC 61000-4-2

±6 kV contact

±8 kV air

±8 kV contact

±15 kV air

Floors should be wood, concrete or ceramic 

tile. If floor are covered with synthetic material,

the relative humidity should be at least 30%.

Electrical fast 

transient/burst 

IEC 61000-4-4

±2 kV for power 

supply lines

±1 kV for input/ 

output lines

±2kV for power

supply lines

Main power quality should be that of a typical 

commercial or hospital environment.

Surge

IEC 61000-4-5

± 1 kV line(s) to 

line(s)

± 2 kV line(s) to 

earth

±1 kV differen-

tial mode

Mains power quality should be that of a typical 

commercial or hospital environment.

Voltage dips, 

short interrup-

tions and volt-

age variations on

power supply 

input lines IEC 

61000-4-11

<5% U

T

(>95% dip in U

T

)

for 0.5 cycle

40% U

T

(60% dip in U

T

)

for 5 cycles

70% U

T

(30% dip in U

T

)

for 25 cycles

<5% U

T

(>95% dip in U

T

)

for 5 sec

<5% U

T

(>95% dip in U

T

)

for 0.5 cycle

40% U

T

(60% dip in U

T

)

for 5 cycles

70% U

T

(30% dip in U

T

)

for 25 cycles

<5% U

T

(>95% dip in U

T

)

for 5 sec

Mains power quality should be that of a typical 

commercial or hospital environment. If the user

of the BW-PFX1 requires continued operation 

during power mains interruptions, it is recom-

mended that the BW-PFX1 be powered from an 

uninterruptible power supply or a battery.

Power frequency

(50Hz/60Hz)

magnetic field 

IEC 61000-4-8

3 A/m

30 A/m

Power frequency magnetic fields should be at 

levels characteristic of a typical location in a 

typical commercial or hospital environment.

NOTE U

T

 is the a.c. mains voltage prior to application of the test level.