3
STEP
• Connect the heart rate wires
coming from the seat rail to the heart
rate wires coming from the main
frame.
• As you slide the seat rail onto the
seat rail bracket, slide any excess
heart rate wire into the seat rail
bracket. Slide the seat rail on so the
holes on the bottom of the bracket are
in line with the frame. Insert three
(M8x15L) bolts with three (SW8) lock
washers into the holes for support. Do
not tighten completely.
• Connect the bottom frame support
tube to the bottom of the rear support
foot with two (M8x20L) bolts and two
(SW8) lock washers. Tighten with the
5mm T-handle wrench.
• Go back and tighten all bolts with the
5mm T-handle or 5mm L-shaped wrench.
PINK BAG
6
STEP
• Attach left and right pedal straps to
left and right pedals.
• Attach left and right pedals to left
and right crank arms.
NOTE: both
pedals and crank arms should be
labeled left or right.
Tighten with the
included pedal wrench.
• Plug in power supply to power
socket on the front side of the bike.
PEDALS
6
STEP
1
STEP
• Connect bottom frame support tube
to main frame with two (M8x15L) bolts
and two (SW8) lock washers. Tighten
with the 5mm T-handle wrench.
ORANGE BAG
To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before
proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in
your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike.
If any parts, hardware or tools are missing, please call 1.800.335.4348
NOTE:
It is recommended that you apply grease to the threads of each bolt and screw as you assemble
your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts
and screws are in place and partially threaded in before completely tightening any ONE bolt or screw.
A s s e m b l y
G u i d e
R1500
SEMI-RECUMBENT FITNESS BIKE
3
STEP
4
STEP
• Slide the console mast cover onto the
console mast.
• Wrap the wire tie that comes from the
bottom of the console mast around the
end of console cable and around the
heart rate wires that are sitting in the
frame console mast bracket. Slowly pull
the wire tie up through the console mast
until the cable and wires come through
the top of the mast. Slide the bottom of
the console mast over the frame mast
bracket. Holding the mast straight, insert
the (M8x10L) set screw into the front
side of the mast and tighten with the
4mm L-shaped wrench. Secure the mast
to the frame with four (M8x15L) bolts
and four (SW8) lock washers on the
sides of the mast and tighten with the
5mm T-handle wrench.
• Remove the four bolts from the back
side of the console. Plug the console
cable and heart rate wires into the back
side of the console. Place the console
onto the mounting plate of the console
mast and re-insert the four mounting
bolts. Tighten with the screwdriver.
• Remove the two bolts from the
backside of the console mast. Attach
the water bottle cage to the mast with
these two bolts. Tighten with the
screwdriver. Insert water bottle.
GREEN BAG
Console Mast
Cover
Console Mast
Water Bottle
Cage
Console Mast
Bracket
2
STEP
• Attach rear support foot to the
bottom of the seat rail with four
(M8x15L) bolts and four (SW8) lock
washers. Do not tighten completely.
• Slide the seat frame onto the seat rail.
Make sure the flat side of the clamp
block rests against the bottom of the
seat rail. Also make sure the adjustment
handle is facing forward.
• Insert the heart rate wires located
under the seat frame through the hole
on the bottom of the seat rail and push
them toward the front of the rail. Take
the end of the heart rate wires that run
through the seat rail and insert them
through the hole in the bracket at the
end of the rail. Snap the wire grip
around the end of the heart rate wires
and snap it into place in the bracket.
• Attach the rubber stopper to the
bottom of the seat rail with the
(M5x10L) bolt. Tighten with the
screwdriver.
BLUE BAG
5
STEP
BLACK BAG
Seat Rail
Wire Grip
Rubber Stopper
2
STEP
1
STEP
4
STEP
5
STEP
Bottom Frame
Support Tube
Seat Frame
Heart Rate
Wires
Heart Rate
Wires
Rear Support
Foot
Heart Rate
Wires
Seat Rail
Bracket
Handlebar
• Connect the Heart Rate wires from the
seat handlebar to the heart rate wires
from the seat frame. Attach seat
handlebar to seat frame with four
(M8x15L) bolts and four (SW8) lock
washers. Tighten with 5mm T-shaped
wrench.
• Attach seat bottom cushion to seat
frame with four (M6x35L) bolts and four
(M6) arc washers. Tighten with the
4mm L-shaped wrench.
• Attach the seat back cushion to the
seat frame with four (M6x35L) bolts and
four (M6) arc washers. Tighten with the
4mm L-shaped wrench.
SIMPLE
DELUXE
PREMIER
CONSOLES
7
STEP
• Refer to
Product Selection and
Model Configuration
decal on
console or follow these steps.
• Once the product is plugged in turn
on the console
• Select product (Bike (BK) or Elliptical
(EP)) using the resistance arrow keys.
Press ENTER to select.
• Select model number (Bike (1500,
2050, 2250, 3200) or Elliptical
(1500, 6000, 6200)) using the
RESISTANCE arrow keys. Press
ENTER to select. Console will reset to
start-up screen.
• The product selection and model
configuration is now complete.
CONSOLE
