Positioning
When positioning the Antenna Dome
please allow for the following:-
1. Place above a wardrobe or locker to
provide
a suitable location for the
Power Amplifier below.
2. Position as high as possible to ensure
Status is not shielded from incoming
signals.
3. Do not place within one metre of
any metal protrusions such as roof
racks, metal flues, metal poles etc. as
this may cause picture distortion.
4. On a Caravan or Motorhome mounting
on
the offside will reduce collision
with overhead obstructions.
Fixing
1. Make a hole 15mm in diameter, large
enough for the coaxial cable with plug
fitted to be passed through, making
sure there are no sharp edges that
could cut or chafe the cable.
2. Remove the Mounting Foot from the
Antenna Dome. Turn the Mounting
Foot
upside down and with a SEALANT
ADHESIVE fill the channel around the
edge, including around the holes for
the fixing screws.
The Antenna Dome
Pole Fitting
INSTALLATION
IMPORTANT - The channel needs to be
slightly over-filled to ensure a good contact.
3. Place in position centrally over the
drilled hole and secure with the four
16mm self tapping screws.
4. Once the sealant has set, thread the
coaxial cable through the roof, pulling
through
the cable as the antenna is
lowered, making sure the cable does
not snag, kink, chafe or become
trapped.
5. Push the Antenna Dome into position,
ensuring it is properly seated in the
Mounting Foot. Secure by tightening
the two grub screws with the Allen
Key.
Angle Adjustment.
Only relevant if you are mounting Status
on a sloping surface. Level fixing is very
important to ensure optimum performance.
1. To adjust the angle, remove the Antenna
Dome from the Mounting Foot and
turn the Antenna Dome upside down.
2. With a screwdriver loosen the Central
Bolt, adjust the Adapter to the desired
angle and re-tighten the central bolt.
3. Push the Antenna Dome into position,
ensuring it is properly seated in the
Mounting Foot. Secure by tightening
the two grub screws with the Allen
Key.
The Power Amplifier
Positioning & Fixing
1. Locate the Power Amplifier in the
wardrobe or locker below the Antenna
Dome where it is easily accessible and
where possible close to the TV position.
2. Fix in place using the two 38mm
screws
Wiring to Power Supply
1. Status requires a 12-24 volt power
supply from a fused auxiliary outlet fed
from the battery. If wiring direct to a battery
we recommend an in-line fuse (max 5
amp) on the positive wire. If unsure
please consult with a qualified installer.
RED VE, BLACK –VE
DO NOT connect into any other 12 volt
power cables as they may carry electrical
interference which will cause picture
distortion.
Connecting the Antenna
1. Shorten the cable from the Antenna
Dome to the required length to reach
the Power Amplifier - DO NOT COIL ANY
EXCESS CABLE.
2. Trim the cable and refit the F-Connector
as described in this guide.
3. Once fitted, connect the Antenna to the
‘ANT.IN’ socket.
DO NOT secure the cable with any staples or ‘P’
Clips as this may damage the cable, it is best
left loose.
Connecting to your Television
To connect to your television you will need
to run a cable to your TV position to the Power
Amplifier. There are many options available
dependant on your particular installation.
You may well require additional cable,
connectors, plugs or sockets which are
available from ourselves or through your
local dealer.
Whenever routing the cable or fitting
connectors please follow our Important
Guideline below.
Operating the System
1. Switch ON the Power Amplifier and the
blue LED will illuminate.
2. Check the gain control switch is set to
maximum by rotating clockwise.
3. Turn on your television set and tune in.
This may be necessary at all new
locations
.
1. Remove the Mounting Foot from the
Antenna Dome.
2. The Adapter is now ready to
accommodate any 25mm pole, such
as those in the Vision Plus Range.
3. The coaxial cable can be threaded
down the centre or outside of the
pole.
4. If the cable is being fed down the
outside please ensure that the top of
the pole does not rub or cut the
coaxial cable when being pushed into
place.
5. Once the pole is in place, secure by
tightening the two grub screws with
the Allen key.
IMPORTANT – Status is not designed to be
used in conjunction with a ‘through-the-
roof’ pole kit.
Removing the Antenna
A permanently fitted Status may be
removed if there are severe height
restrictions, leaving only the Mounting Foot
in place.
1. Disconnect the Antenna from the Power
Amplifier. On the Adapter loosen the
two grub screws with the Allen key
and lift off whilst carefully feeding out
the coaxial cable with plug attached.
2. Push the Blanking Cap supplied into
place to cover the central hole.
This may be necessary should you wish to
reduce the overall height of the antenna by
90 mm.
1. Simply unscrew the Pinnacle and
remove. The antenna is designed to
remain water tight without the
Pinnacle.
2. To replace, simply screw in and tighten
BY HAND.
3. IMPORTANT - The Pinnacle is an
integral part of the antenna and
critical to its performance. When in
use always ensure the Pinnacle is fitted.
Removing the Pinnacle
Grade UK Limited
8 FinchClose
Lenton Lane
Nottingham NG7 2NN
Tel: 0115 986 7151
email: info@gradeuk.co.uk
www.gradeuk.co.uk
