background image

Concrete Floor Option

Concrete Floor Option
You may decide to construct your Vision storage 

shed on a concrete foundation, in which case it is 

recommended that you engage the services of a 

concrete contractor.

Prior to having a concrete foundation poured 

please perform the following:

• Make sure your structure will comply with local  

  building codes and ordinances.
• Select a location that is free from ground water  

  and provides suitable drainage, that can be  

  leveled properly and affords ample room to  

  erect  the shed.

97-1/8"

88-1/4"

Consult your concrete contractor  

about the following:
• Ask your contractor to confirm the specifications for the concrete 

 

  thickness required for your locate climate and soil type. Certain  

  building codes may apply as well.

• Request the concrete foundation be made 2-inches larger around  

  all sides than the overall dimensions of the storage shed. This  

  will afford adequate space for drilling anchor holes and inserting  

  fasteners to secure the shed base track to the concrete, thereby  

  avoiding possible cracking or chipping of the concrete surface.

• Confirm that moisture barrier will be laid before the concrete 

 

  is poured.
• Request the foundation surface to be free of bumps and ridges.  

  Be sure concrete is level to prevent water from collecting at the  

  front door opening of the building.
• (Optional) Inquire whether concrete sealer/paint should be  

  applied to the cured floor to prevent moisture build-up in 

 

  the structure.

72-1/2"

93-1/8"

84-1/4"

Overall Shed 

Dimensions

Recommended Concrete 

Foundation Dimensions

5

Summary of Contents for S-8070-A
















Reviews: