background image

INTRODUCTION   

The VIS-3009 is single door multifunction standalone access controller or a Wiegand output card reader. It uses 

Atmel microcontroller assures maximum performance in any environment, and the low-power circuit makes its 

service life prolonged.   

 

The VIS-3009 supports 1,000 users (998 common users + 2 panic users), all user data can be downloaded and 

uploaded. It has extra features including block enrollment, interlocked, 

Wiegand 26~37 bits interface…etc.   

 

Features 

 

Waterproof, conform to IP66 

 

One relay, Remote infrared programmer 

 

1,000 users (998 common users + 2 panic users) 

 

User data can be downloaded and uploaded 

 

With Wiegand 26~37 input & output 

 

Pulse mode, Latch mode

 

 

Card block enrolment 

 

Tri-colour LED status display 

 

Built in light dependent resistor (LDR) for anti tamper 

 

Integrated Alarm Buzzer & Output 

 

Low temperature resistance (-40°C) 

 

Specifications: 

User Capacity   

Common User 

Panic User 

1000 

998 

Operating Voltage   

Idle Current 

12~24V AC/DC 

35mA   

Proximity Card Reader 

Radio Technology   

Read Range 

EM 

125KHz Proximity Card 

2~6 cm (0.78~2.36 in.) 

Wiring Connections   

Relay Output, Exit Button 

Relay 

Adjustable Relay Output Time 

Lock Output Load 

One (NO, NC, Common) 

1-99 Seconds (5 seconds default) 

2 Amp Maximum 

Environment 

Operating Temperature 

Operating Humidity   

Meets IP66 

-40°C ~60°C (-40°F ~ 140°F) 

0%RH-98%RH 

Physical 

Colour 

Dimensions 

Unit Weight   

Shipping Weight 

ABS Shell 

Black 

102L x 48W x 20H (mm) 

– 4.01L x 1.88W x 0.78 (in.) 

125g 

150g   

Summary of Contents for VIS-3009













Reviews: