INSTALLATION INSTRUCTIONS
1625 Surveyor Avenue • Simi Valley, CA 93063 • (805) 527-0987 • (800) 766-VISTA (8478)
FAX: (888) 670-VISTA (8478) • email@vistapro.com • www.vistapro.com
Vista Professional Outdoor Lighting reserves the right to modify the design and/or construction of the fixture shown without further notification.
Step & Brick Lights
Landscape Series
4260
FOR USE ONLY WITH LOW VOLTAGE LANDSCAPE POWER UNITS THAT DO NOT EXCEED 25 AMPS, 15 VOLT MAXIMUM.
WARNING:
Luminaires must be installed in accordance with the National Electrical Code (NEC) and local codes. Failure to do so will void the
warranty and may result in serious injury and/or damage to the luminaire.
SAFETY WARNING:
Luminaire can become very hot depending on lamp wattage used. Lens and metal around lamp can become hot enough to
blister hands. Particular care should be taken not to locate luminaires where small children can reach them if high wattage lamps are used.
LUMINAIRES ARE NOT TO BE INSTALLED WITHIN 10 FT. (3.05M) OF A POOL OR SPA. SECONDARY CABLE IS NOT TO BE BURIED MORE
THAN 6”. WHEN USING MULTIPLE LUMINAIRES, LOAD IS NOT TO EXCEED THE TOTAL WATTS OF TRANSFORMER RATING. DO NOT USE
EXTENSION CORDS ON POWER UNITS.
NOTE:
Always use UL recognized wire connectors for connections.
NOTE:
Save these instructions for future reference.
RAIL AND DECK MOUNTING:
1. To prevent electrical shock, disconnect transformer from electrical
supply before installation or service.
2. Loosen cover screws and remove front cover plate.
3. Slide frosted lens out from retaining bracket in fixture housing.
4. Route luminaire pigtail wire up through wiring access hole in fixture
chassis, or through wiring access notch in rear cover plate (access
notch allows for rear or side routing of pigtail wire).
5. Check position of weather-tight gasket on top side of fixture chassis,
and adjust if necessary.
6. Mount fixture chassis to bottom side of fence rail, deck over-hang, or
other flat surface.
7. Replace lens, sliding it into retaining bracket in fixture chassis.
8. Replace cover plate and tighten cover screws evenly.
9. Route wire through rail or deck to main power supply cable.
10. Strip two leads from luminaire pigtail wire.
11. Using two silicone filled safety connectors, connect leads from
luminaire to main supply cable leads.
NOTE:
Luminaires are supplied with 60” of 18-2 cable pigtail for secure
connection to main supply cable.
12. Provide power to luminaire and check for proper operation.
PAVER-WALL MOUNTING:
1. To prevent electrical shock, disconnect transformer from electrical
supply before installation or service.
2. Route luminaire pigtail wire through wiring access notch in rear cover
plate (access notch allows for rear or side routing of pigtail wire).
3. Check positioning of weather-tight gasket on the top side of fixture
chassis, and adjust if necessary.
4. Mount stainless steel mounting plate to the top of the fixture chassis
using the flat-head machine screws provided.
5. Insert stainless steel mounting plate between layers of hardscape
material (as an option, adhesive may be used to secure fixture position).
6. Route wire through wall to main power supply cable using standard
masonry procedures.
7. Strip the two (2) leads from the luminaire pigtail wire. Using the two
(2) silicone filled safety connectors (provided), connect the leads from
the luminaire to the main supply cable leads.
NOTE:
Luminaires are supplied with 60” of 18-2 cable pigtail for secure
connection to the main supply cable.
8. Provide power to the luminaire and check for proper operation.
MOUNTING PLATE MODIFICATION:
1. Using a standard circular saw with masonry compatible minimum 9”
blade, cut a slot into the existing block or mortar joint.
2. Remove “snap off” corners allowing the mounting plate to conform to
the standard circular saw cut.
3. Using pliers, lift tiger grips just enough to secure fixture once in
position.
WEATHER-TIGHT
GASKET
MOUNTING
PLATE
