Mounting Brackets: Smooth Lift - Cordless - Rechargeable Motorization
Mounting Brackets: Cord Lift - Lift&Lock Cordless
Optional Hold Down Brackets
Optional hold down brackets are mounted with the supplied screws. With the shade at its full drop, place the pins on the hold down brackets into the
holes in the bottom rail end cap and mark the mounting location (Fig 17).
Make sure the pins are level and aligned. Raise the shade, then screw the brackets onto the mounting surface.
Leveling the Bottom Rail
Child Safety
Care and Cleaning
INSIDE MOUNT
Position the first two brackets 3'' from the ends for Smooth Lift Control shades and 1 1/2'' from ends for Cordless or Motorized shades.
Evenly space any additional brackets between the two end brackets. Brackets may be mounted to ceiling, or the top or inside of window frame.
Inside or ceiling mount uses the top bracket holes.
To attach the brackets the flat surface of the window casement must be at least 3/4'' deep.
To fully recess the shade the flat surface must be at least 2 3/4'' deep (Fig. 1).
Note:
Release tab is at the bottom of the bracket.
Shade Width
# Brackets
Up to 60''
2
60 1/8'' - 96''
3
96 1/8'' - 132''
4
132 1/8'' - 168''
5
Cellular shades use a system that allows easy leveling of the bottom rail. It is designed to make slight adjustments (less than 1'') to level the moving rails
of your shade. It is not designed to make shade length adjustments. (Fig. 18)
Use a flat head screwdriver to turn the adjustment screw to raise or lower either side of the bottom rail. The adjustment screw is located on the
underside of the rail.
One quarter turn of the screw will move the bottom rail up or down approximately 1/4'''. Over-turning the adjustment screw (more than 1'') can cause
the cord to tangle or get pinched inside the rail.
The screw should turn easily. Do Not Force.
LIFT & LOCK
Make adjustment with leveling tool found in the bottom rail behind the right end cap. Remove the endcap and pull out the section labeled TOOL (Fig. 19).
Push in on the adjustment screw with the tool and turn to adjust the rail.
Turning clockwise will move the rail down, counter-clockwise will move the rail up (Fig. 20).
When the rail is level, replace the tool and the endcap.
© 04/19
K2176
An important consideration in any shade installation is child safety. To prevent serious injuries or strangulations, all cords must be kept out of the reach
of children. Cord cleats or other methods of keeping the cords from hanging within reach of a child should be utilized.
Cellular Shades also include breakaway tassels that will separate and prevent the lift cords from traveling backwards through the cordlock.
The tension device reduces the hazards of strangulation and entanglement of young children and pets by limiting access to the control loop.
The tension device must be installed to make the shade fully operational.
Pull tension device down until the chain is taut on both sides. Mark the upper screw hole, and using screws provided, install tension device with upper
hole 3/8'' above mark.
Young children can become entangled and strangle in cords. Keep all cords out of the reach of children.
WARNING:
OPERATING INSTRUCTIONS:
CORD LIFT
Pull the lift cords straight down to raise and lock the shade into position. Pull the lift cord toward the center of the shade to unlock and lower.
SMOOTH LIFT CONTINUES CORD LOOP
Continuous control loop offers precise shade positioning while the control remains the same length. Come with tension device that must be mounted in
order for the shade to operate.
CORDLESS LIFT
Raise and lower the shade by gently pulling or pushing on the bottom rail.
LIFT & LOCK CORDLESS
Operate the shade by pressing a button in the bottom rail and lock in place by releasing the button.
RECHARGEABLE MOTORIZATION
Control a single shade or a group of shades with one remote. See separate Programming In
structions for additional set up information.
CELLULAR SHADES
I
nstallation & Operating Instructions
K2176
1 1/2''
2 3/4''
(Fig. 1)
3/4''
1 1/2''
(Fig. 2)
Shade Width
# Brackets
Up to 60''
2
60 1/8'' - 96''
3
96 1/8'' - 132''
4
132 1/8'' - 168''
5
INSIDE MOUNT
Position the first two brackets 2 1/2'' from the ends of the shade. Evenly space any additional brackets between the two end brackets.
Brackets may be mounted to ceiling, or the top or inside of window frame.
To attach the brackets, the flat surface of the window casement must be at least 1'' deep for small rail or 1 5/8’’ deep for large rail. To fully recess the
shade, the flat surface must be at least 1 5/8'' deep for small rail or 2 7/16'' deep for large rail. (Fig. 3)
(Fig. 3)
OUTSIDE MOUNT
Position the first two brackets 3’’ from the ends for Smooth Lift Control shades and 1 1/2’’ from ends for Cordless or Motorized shades.
Evenly space any additional brackets between the two end brackets.
The brackets are mounted using the rear bracket holes. (Fig. 2)
Mount the installation brackets on a flat vertical surface at least 3/4’’ high.
NOTE:
If motorized shade has an external battery pack, spacer blocks are required for outside mount application.
Shades should be raised fully on a regular basis to ensure fabric pleat retention.
DUSTING & VACUUMING
Cellular Shades can be dusted regularly to keep them looking new. Use a soft, clean cloth, dusting mitt, or chemically treated dust cloth. Shades may also
be cleaned by vacuuming them with the brush attachment of a vacuum cleaner.
SPOT CLEANING
Most stains can be blotted with a damp sponge and mild detergent.
Important:
Do Not Immerse shade fully in water. Ultrasonic cleaning is not recommended.
(Fig. 17)
(Fig. 18)
(Fig. 19)
(Fig. 20)
