background image

Recommended separation distances between portable and mobile RF 

communications equipment and the Infrared Body Thermometer.

The 4 in 1 contactless infrared body thermometer is intended for use in an 
electromagnetic environment in which radiated RF disturbances are controlled. 
The customer or user of the 4 in 1 contactless infrared body thermometer can help 
prevent electromagnetic interference by maintaining a minimum distance between 
portable and mobile RF communications equipment (transmitters) and the 4 in 1 
contactless infrared body thermometer as recommended below, according to the 
maximum output power of the communications equipment.

For transmitters rated at a maximum output power not listed above, the 
recommended separation distance “d” in metres (m) can be estimated using the 
equation applicable to the frequency of the transmitter, where “p” is the maximum 
output power rating of the transmitter in watts (W) according to the transmitter 
manufacturer. 

NOTE:

 At 80 MHz and 800 MHz, the separation distance for the 

higher frequency range applies. 

NOTE:

 These guidelines may not apply in all 

situations. Electromagnetic propagation is affected by absorption and reflection 
from structures, objects and people.

Rated maximum 
output power of 

transmitter 

(W)

150 KHz to 80 MHz

d=1,2

p

80 KHz to 800 MHz

d=1,2

p

800 KHz to 2.5 MHz

d=2,3

p

Separation distance according to frequency of transmitter 

(m)

 0.01 

0.12 

0.12 

0.23

 0.1 

0.38 

0.38 

0.73

 1 

1.2 

1.2 

2.3

 10 

3.8 

3.8 

7.3

 100 

12 

12 

23

Guidance and manufacture’s declaration – electromagnetic emission

The 4 in 1 contactless infrared body thermometer is intended for use in the 
electromagnetic environment specified below. The user of the Infrared Body 
Thermometer should assure that it is used in such an environment.

80 KHz to 800 MHz

d=1,2

p

800 KHz to 2.5 MHz

d=2,3

p

Emission test

Compliance

RF emissions CISPR 11

RF emission CISPR 11

Harmonic emissions IEC 61000-3-2

Voltage fluctuations/ flicker emissions 

IEC 61000-3-3

Group 1

Class B

Not applicable – the 4 in 1 contactless 

thermometer is solely 

battery powered.

www.vitalbaby.com

Summary of Contents for PROTECT HTD8216C















Reviews: