Vitavia 6722003 Assembly Instructions Manual Download

Page: 5 / 86

doors on the door gliders (1014) to avoid
damaging them.

Push the door gliders (1014) onto both ends of
door bar (1360) (5.1).

Assemble the doors as shown in diagram 5.

Bolt door bar (1362) to upper bar (1359) (5.3)
and slide door seals (2021) into door bars
(2058) (5.5). Slide bolts (1500) into the bottom
of the bolt channel holding brush seals (2021)

and ix it in place using nut (1515) (5.6). Cut

the door seals (2021) to length. Please ensure
that for the inside side bar the part (2098) is
used on the left in (5L) and (2099) on the right
in (5R).

Connect door rollers (1015) to the door bar
(1362) using bolt (1304), washer (1009) and
nut (1007) (5.4).

Connect bolt (2001) at the join between both
(1347) as shown (5R).

Loosen the door supports (2043).

Now slide the door rollers into the door runner
bar (1347) (5.7). Please ensure that the door
gliders are also running on the bottom track
(5.8).

Adjust the doors so that they move freely.

6. RooF veNtS

Connect the side bars (1065) and the top bar
(1064) depending on the glass thickness.
Up to 4 mm, see (6.1). For 4 mm and over,
see (6.2).

Place the bolts to connect the bottom bar
(1066) in the prepared holes, and then slide
the glass into the tracks in side bars (1065)
(6.3).

Now connect bottom bar (1066), and ensure
that the window is totally square before
tightening all bolts.

Position the window in the ridge bar from one
end (6.4) and (6.5) and slide it to the required
position (6.6).

Connect the window sill (1063) with the extra
bolts in the roof bars (6.7).

Bolt the window opener (1067) to the bottom
bar (1066) using screws (1006) (6.8).

Place the plastic cap (1019) over the end of
the window opener (6.6) and connect both

window ixers (2016) onto the window sill

(1063) using screws (1006) (6.8).

7. GlazING – cleaR / FRoSteD GlaSS

Please note the already mentioned safety
precautions.

Press the glazing seals (1020) onto the

aluminium proiles (7.3) and cut to length.

On the roof begin by positioning the glass at

the eave and ix in place using the glazing

spring clips (1011) (7.2). The following pane
should be placed over the pane directly under
it and held in place with the glass retaining
clips (1012) between the panes (7.1).

On the sides please begin from the bottom.

If you’ve chosen polycarbonate sheets instead
of glass panes, please use the instruction
included in the box with the polycarbonate
sheets.

FINIShING

If desired, it is possible to seal the greenhouse
at the edges using neutral silicone. Silicone is
not in cluded.

Place the warning label inside the house.

A full range of accessories is available to help
you make the most of this product. Please
contact your local stockist for details.

SaFety NotIce

In the event of high winds, close all doors and
vents.

In the event of heavy snowfall, clear the roof of
the building or take suitable measures to
support the roof. Heat the building in winter.

commeNtS

For the complete protection of your new
greenhouse, we advise you to include it in
your house insurance. Please take note of
possible building rules relating to the
positioning of greenhouses.

Please stick the greenhouse model label
provided onto the door bar (1362) after
successfully assembling this product. This
information is important in the event that
replacement parts are later required.

Please keep these Assembly Instructions in
a safe place, for future reference!

Our policy is one of continuous improvement
and we reserve the right to change the

speciications without prior notice.

001.01.2009