6
SIte SelectIoN
Always try to select a sunny location, sheltered
from the wind as much as possible.
ImPoRtaNt
Before assembling your new greenhouse,
please check that all parts in the provided list
are included. Please take each bundle out of
the packaging in order to identify the parts
better.
It is important that the opened bundles do not
get mixed with one another.
If something is missing please contact your
retailer.
Nuts (1002) - max. tightening torque 3Nm.
NeceSSaRy toolS
Screw drivers (Normal and Crosshead PH2),
10 mm socket spanner or wrench, 10 mm
combination spanner, knife, measuring stick,
spirit level, Accu-drill with adjustable torque.
maINteNaNce
The greenhouse should be thoroughly washed
with a gentle detergent occasionally. Please
check that the detergent used does not react
aggressively with aluminium or the glass ixing
clips.
Ensure that the upper and lower door tracks
are cleaned regularly to avoid a build-up of
debris.
0a. BaSe
Important!
The base must be exactly square
and level.
Foundations must extend down below the frost
level.
The front must allow room on the foundation,
minimum 70mm, for the support of the door
guide (2070) in section 4B.
Diagrams in a single frame show the view
from inside the greenhouse. those
enclosed in a double frame show the view
from outside the greenhouse.
0B. Wall
Build a wall 500mm high on the prepared
foundation as shown, with an opening of
1218mm in the front.
The front must allow room on the foundation,
minimum 70mm, for the support of the door
guide (2070) in section 4B.
Important!
The wall must be exactly square
and level.
(
attention!
Only when the greenhouse has to
be located in a very windy and unprotected
location:
Drill through the proiles at the base
of the greenhouse and connect them to the top
of the wall. Screws and wall plugs are not
included.)
1. SIDe elemeNtS
Lay all of the parts on the loor and connect
them loosely.
At this stage it is necessary with each vertical
aluminium bar (2072) to include an extra
connecting bolt, to connect corner braces
(2056) (1.4).
Loosely connect the corner plate (1092) (1.1).
In step 4 the corner plate bolts must also be
connected to the Gable ends.
2. PlaIN GaBle eND
Lay all of the parts on the loor and connect
them loosely.
Include one extra connecting bolt in the
vertical bars (2067, 2068 and 2071) to connect
the cross braces (2.2).
3. DooR GaBle eND
Lay all of the parts on the loor and connect
them loosely.
The door runner bars (1347) will be connected
to the horizontal bar (2048). Connect each of
these loosely from the outside with three bolts
and two nuts.
Connect (5001) and (5002) as shown in (3.9)
(3.10) with a nut.
As in step 2, please include one extra bolt in
both vertical bars (2067) and (2068) (3.3).
4a. coNNectING the SePaRate
elemeNtS
Bolt the side elements to the end elements
(4.1) & (4.2).
Loosely connect the corner plate (1092) above
the eaves (4.3).
Assemble the ridge bar and then the corner
plates (1092) on the Gable ends (4.4/4.5).
Connect the door runner supports (2043) to
the door runner bars (1347) using washer
(6060) (4.1) and to the Gable end using bolt
(4201) and spacer (1310) (4.3) (4.6).
4B. coNNectING the SePaRate
elemeNtS
Lift the assembled structure onto the prepared
wall and connect loosely using clips (9104)
(4.9). Screws and wall plugs are not included.
Loosely connect the door runner bar (2070) to
the front of the wall (4.7) (4.8) using the 4
holders (2059) and countersunk screws (not
included).
Connect the roof glazing bars (2055) between
the eaves (4.10) and the ridge bar (4.11).
Insert extra bolts into each glazing bar
depending on which house you have bought.
The number is indicated in a circle on each bar
and to be read beginning from both ends.
063.01.1809
1. PLEASE READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE ASSEMBLING YOUR GREENHOUSE.
2. Sharp edges and corners can cause injury. Always wear protective glasses, gloves, shoes and headgear when handling the aluminium proiles, glass and
polycarbonate sheets. Broken glass is a safety hazard – always clear up immediately and dispose of with care.
3. The product you have purchased is intended only for growing plants and should only be used for this purpose. When used for other purposes we will take
no responsibility.
4. It is recommended that this greenhouse is assembled by two people.
5. Should you encounter dificulties constructing this house, or in itting the glass or polycarbonate sheets, please contact your retailer
– do not use force!
6. The greenhouse must always be anchored.
Assembly Instructions
Safety Warning
EN
Summary of Contents for Cassiopeia 11500
Page 5: ...5 063 01 1809...
Page 31: ......
