Vitavia Hera 2 9000, Assembly Instructions Manual

5

011.02.1108

In 5L connect bolt extender (6055) and latch 

(6050) (5L.6).

In 5R note the position of the prepared holes 

in (6016) for the handle and lock. Assemble 

the door handle as shown (5R.6).

Ensure that the door is totally square before 

tightening all bolts. This can be done by 

measuring the diagonals.

Connect the plastic door guides (6057) onto 

bar (6014) with screws (6062) (5.2). 

Loosely connect the door wheels (6049) and 

door jump clips (6039) to bottom bar (6017) 

using bolt (6046), washers (6051) and nut 

(3002) (5.4). These should be tightened when 

the door is later fitted in the building.

Repeat for both doors and lay them aside for 

later use.

 6. veNtS  

The position of vents is determined by the 

location of the prepared holes in eave angle 

(6072).

Note:

Warm window seal (6034) to room 

temperature!

 Press seal (6034) centrally onto 

the top edge of glass pane (C) (6.1). 

Do not 

stretch.

Make a cut into the seal at the corner (6.2) and 

then press the seal onto the side and bottom 

edges of pane (C), cutting to fit around each 

corner. 

Fit vent bottom bar (6024) over the seal 

(6.3) and then side bars (6020) and (6021). 

Connect these at the corners using screws 

(1003) (6.4).

Finish pressing the seal onto the top edge and 

cut to length in the middle. Fit the top vent bar 

(6025) and connect to side bars (6020) and 

(6021) with screws (1003) (6.5).

Ensure that the vent is totally square before 

tightening all screws. 

Loosely connect bar (6066) using bolt (3001) 

onto eave angle (6072) using the prepared 

holes (6.6).

Remove side brace (6003) and diagonal brace 

(6008) to fit vent sill (6019) behind them (6.7).

Replace (6003) and then (6008), loosely 

connecting with nut (3002) (6.7) (6.8). Do 

not tighten until the roof vent is assembled in 

building. 

Repeat for all vents and lay them aside for 

later use.

 7. glazINg  

Please note the already mentioned safety 

precautions.

Ensure that the U/V protected face of all 

polycarbonate sheets is on the outside.

With one person using the step ladder inside 

the building, glaze the roof by sliding panes 

(D),(E) and (F) into the appropriate guides in 

the roof bars (6087) and (6088) (7.2) (7.3). 

When adjacent panes are in place connect 

ends (6077), (6078) or (6079) using screws 

(7349) (7.4) to prevent them sliding out of the 

guides.

Position door guide bar (6074) onto eave 

angle (6072) / (6073) and fix in place using 3 

equally spaced screws (6068) (7.6) (7.7).

Press the glazing seals (1020) onto all side 

bars (6013) and (6022) (7.5) and cut to length. 

Fit the glazing panes (G), (H) and (J) as 

shown and fix by pressing plastic fixing strips 

(6030) or (6032) onto each side (7.6) & (7.7).

Now tighten the bolts connecting the building 

to the foundation.

 8. PoSItIoNINg of veNtS aND DooRS

Lift the vents into the prepared positions in 

the sides by loosening bar (6066) and sliding 

bar (6025) into bar (6066) from one end (8.1) 

& (8.2). Lift vent sill bar (6019) and fit it to the 

vent. When correctly positioned tighten all 

bolts on the inside.

Bolt the vent opener (1067) onto bar (6024) 

using screws (6062) (8.3).

Connect both vent fixers (6056) onto sill bar 

(6019) using screws (6062) (8.3).

Place the plastic cap (1019) over the end of 

the window opener (1067) (8.3).

Position the doors by inserting the plastic door 

guides (6057) into bar (6074) (8.4) (8.5) and 

then lower the wheels onto the door track on 

bar (6002) (8.6). Hook the door jump clips 

(6039) under the lip on (6002) and tighten the 

door wheel bolts (6046) (8.6) (8.7).

Connect plastic nut caps (6070) by pushing 

them onto all visible nuts (3002) inside the 

building (8.8).

Connect down pipe elbow (1402) to down 

pipe (1415). At 3 not adjacent corners connect 

the down pipe assembly (1402) / (1415) to 

eave ends (6067) (8.9). Hook clamp (1414) 

onto corner bars (6022) at the height of elbow 

(1402) and insert screw (1006) into the prepa-

red hole in (1414) (8.10). Use the ø 20 drill to 

make the drainage holes in the 3 eave ends 

(6067) noting the marked area.

Inside the greenhouse slide glazing spacers 

(6075) or (6076) onto eave angles (6072) / 

(6073). Fix these to eave angle (6072) central-

ly using screw (7349). (8.11) (8.12).

 fINIShINg 

If desired, it is possible to seal the greenhouse 

at the edges and between the glazing and 

spacers (6075) or (6076) using neutral silicone. 

Silicone is not in cluded.

Place the warning label inside the building.
A full range of greenhouse accessories, to 

help you make the most of this product, is 

available from your stockist. Please inform 

yourself as to the possibilities.

 Safety NotIce 

In the event of high wind conditions, close the 

doors and all vents. 
In the event of heavy snowfall, clear the roof  

of the building or take suitable measures to 

support the roof. Heat the building in winter.

 commeNtS 

For the complete protection of your new 

green house, we advise you to include it in 

your 

house insurance.

 Please take note  

of possible building rules relating to the  

positioning of greenhouses.
Please stick the included greenhouse model 

label onto the door bar (6014) after success-

fully assembling this product. This information 

is important in the event that replacement 

parts are later required. 
Please keep these Assembly Instructions in a 

safe place, for future reference!
Our policy is one of continuous improvement 

and we reserve the right to change the specifi

-

cations without prior notice.