Vitek VT-1350, Manual Instruction

 ENGLISH

5

– 

For lubricating the blades use only the 

oil (11), supplied with the unit, or the oil 

intended for similar devices.

– 

Do not use vegetable oil or oil that 

includes solvents. Solvents will evapo-

rate, and the remaining thick oil may slow 

down the blades motion.

INSTALLING THE ATTACHMENT

– 

Before installing or removing the attach-

ments (6, 7, 8, 9) switch the unit off by 

setting the switch (3) to the position “0”.

– 

Install the selected attachment (6, 7, 8, 9) 

on the blades (1), press on the lower part 

of the attachment (6, 7, 8, 9) to fix it. Make 

sure that the attachment is locked on its 

installation place. 

– 

To remove the attachment (6, 7, 8, 9) press 

on the lower part and remove the attachment.

HAIR STYLING INSTRUCTIONS

• 

Hair should be clean and dry during hair 

cutting.

• 

Before cutting hair switch the hair clipper on 

by setting the switch (3) to the position «I» 

and make sure that the hair clipper operates 

normally and the blades move smoothly. If 

there is excess oil on the blades, switch the 

hair clipper off setting the power switch (3) 

to the position «0» and remove the excess 

oil with a dry cloth.

• 

Seat a person so that his/her head is 

approximately at your eye level, cover the 

person’s shoulders with a towel and set hair 

with the comb.

Reminder

– 

Cut off a little amount of hair at a time; if 

necessary you can always return to the cut 

off part and trim off additional hair.

– 

The best haircutting results are reached 

on dry hair, not wet.

– 

Comb the hair to reveal uneven locks.

– 

It is better to leave longer hair after cutting 

for the first time.

– 

After learning your clipper better, you will 

be able to arrange your hair in any style 

you need.

Step one

Install the attachment (6 or 7). Switch the unit 

on using the power switch (3), setting it to 

the position «I». Hold the hair clipper with the 

blades pointed upwards. Start cutting from the 

beginning of the hair growth. Slowly move the 

clipper upwards. This way cut the head back 

area at the neck bottom and near the ears.

Step two 

Switch the hair clipper off using the switch (3) 

by setting it to the position «0» and install the 

attachment (7 or 8) for cutting longer hair, 

switch the hair clipper on and continue cutting 

hair near the top of the head.

Step 3 – cutting in the temples area

Switch the hair clipper off, install the attachment  

(6 or 7) and cut hair on the temples. Then 

install the attachment (8 or 9) and continue 

cutting towards the top of the head.

Step 4 – cutting the crown of the head

Using the attachment (8 or 9) cut the hair from 

the top of the head towards the crown against 

the hair growth direction.

• 

You can cut hair against and along the direc-

tion of hair growth, but keep in mind that the 

hair cut against the growth will be shorter 

than the hair cut along the growth.

• 

Use the attachments (6 or 7) for very short 

cutting. To leave a little longer hair, use the 

attachments (8 or 9).

• 

To leave longer hair, take hair locks between 

your fingers and cut hair using the hair 

clipper.

• 

You may use a comb: lift the hair locks and cut 

them with the hair clipper above the comb.

• 

Always start cutting from the head back.

• 

Comb the hair to reveal uneven locks.

Step 5 – the final part

In the final stage of hair styling remove the 

installed attachment from the clipper, turn 

the blades of the clipper towards the hair and 

trim hair on the temples and neck carefully.  

Do not press the clipper strongly, there is 

danger of injuries or cuts when open blades 

come in contact with skin.

Note: 

during the breaks between operations 

switch the hair clipper off, setting the power 

switch (3) to the position «0».

• 

After you finish cutting hair switch the hair 

clipper off, setting the power switch (3) to 

the position «0».

• 

Remove the attachment and clean it off 

hair, remove the blade block (1) and clean 

it with the brush (10).