9
ENGLISH
RECIPE
Filling
Mutton 100 g
Olive oil 1.5 tablespoon
Onion (minced) 1.5 tablespoon
Spice to taste
Salt 1/4 teaspoon
Flour 1 tablespoon or 1/2 tablespoon
•
Mince the mutton meat once or twice in the meat
grinder.
•
Fry onion in oil until it turns gold-yellow, then
add minced mutton meat, all spices, salt and
flour.
Casing
Lean meat 450 g
Flour 150-200 g
Spice 1 teaspoon (to taste)
Nutmeg 1 pc.
Cayenne (to taste)
Black pepper (to taste)
•
Mince the meat thrice, mince a nutmeg, and mix
all the components.
•
More meat and less flour in the casing provide
better consistency and taste of the prepared
dish.
•
Fill the rolls, clamp at the edges and shape as
you wish.
•
Deep fry the rolls.
BLENDER ATTACHMENT
USING THE BLENDER
The blender is used for chopping foodstuffs, ice,
mixing various ingredients and making mixed
drinks.
•
Remove the lid (13) upwards (pic. 8).
•
Set the blender bowl (25) on the motor unit (8)
and turn it clockwise as far as it will go, the
bowl (25) handle (26) should be on the right side
of the motor unit (8) (pic. 9).
•
Remove the blender bowl lid (24).
•
Put the necessary ingredients into the
bowl (25).
•
Cover the blender bowl (25) with the lid (24),
insert the measuring cup (23) into the lid (24)
opening.
•
Make sure once again that the blender bowl (25)
is installed correctly and fixed.
•
Insert the power plug into the mains socket.
Note:
- the kitchen machine will not switch on if the
blender bowl (25) is installed incorrectly.
•
Switch the kitchen machine on by turning the
operation mode switch (11), set the required
operation speed from “1 to 6” or to the pulse
mode “P”.
«1» (low speed) – for mixing liquid foodstuffs.
«6» (high speed) – for liquid and hard
foodstuffs.
«P» – pulse mode.
•
To switch the pulse mode on, set the switch (11)
to the position “P” and hold down it for several
seconds.
•
During the operation or between the operation
cycles, you can add the required ingredients into
the bowl (25). To do this, remove the measuring
cup (23), you can use the measuring cup (23) as
a bowl for adding necessary liquid ingredients.
After adding ingredients, install the measuring
cup (23) back to its place.
•
After you finish operating, set the operation
mode switch (11) to the position «0» and unplug
the unit; only after that you can start disassem-
bling the blender bowl (25).
•
Remove the blender bowl (25) from the motor
unit (8) by turning it counterclockwise.
•
Remove the lid (24) from the bowl (25) and take
the processed foodstuffs out of the bowl (25).
•
After the operation is finished, wash the blender
bowl (25).
Note:
- if food processing is hard, add some liquid
(water, liquor, juice) into the blender bowl (25).
•
Before starting to chop/mix, we recommend to
peel fruit, remove inedible parts, such as stones,
and cut fruit into cubes about 2х2 cm in size.
ATTENTION!
Continuous operation time of the
blender should not exceed 30 seconds, and the
break between operations should be 5-10 minutes.
•
After removing the blender bowl (25), install
the lid (13) back to its place; if the lid (13) is not
installed, the kitchen machine will not switch on.
Note:
- if the kitchen machine does not switch on,
set the operation mode switch (11) to the position
“0”, lift and lower the lid (13), check the operability by
briefly setting the switch (11) to any position “1----6”.
OVERHEATING PROTECTION
The overheating protection system will switch the
kitchen machine off if the electric motor operating
temperature is too high. If during the operation the
kitchen machine switches off, set the operation mode
switch (11) to the position «
0
» and unplug the unit.
Let the kitchen machine cool down for 30-40 min-
utes and switch it on again.
Do not exceed the specified operation time and do
not overload the kitchen machine with foodstuffs
during the operation.
IM VT-1439.indd 9
29.11.2018 17:22:10
