7
ENGLISH
release the clamp (21) and check the fixation
of the geared lid (15).
•
Put the motor unit (4) on the geared lid (15)
and turn it clockwise until fixing.
•
Insert the plug into the socket.
•
Set the required speed 1-20 using the con-
trol (1).
•
To switch the blender on press and hold the
button (2).
•
When the button (3) is pressed, the disc
rotates at maximal rotation speed.
•
Place the products into the lid chute (15), use
the pusher (14) for products feeding. Press
the pusher gently for products feeding.
•
After you finish using the unit, take the plug
out of the socket, disconnect the motor unit
(4) from the geared lid (15) by turning it coun-
terclockwise.
•
Then remove the geared lid (15) from the
bowl (22) by pressing the clamp (21) and
turning the lid clockwise.
•
Carefully remove the disc.
•
Take the chopped products out of the pro-
cessing bowl (22).
•
Clean, wash and dry all the used parts imme-
diately after the end of operation.
USING THE CUBIC ATTACHMENT
Use the cubic attachment for cutting fruit and
boiled vegetables.
Attention!
–
Do not process hard and frozen food. It can
damage the cubic attachment.
Warning:
–
Before assembling make sure that the power
plug is not inserted into the socket.
•
Open the clamps (19), set the knife (17) on
the cubic attachment (18) and fix it with the
clamps (19).
•
Match the groove on the cubic attachment
(18) with the ledge inside the processing bowl
(22) (near the handle) and install the attach-
ment in the bowl (22)
(PIC. 1)
•
Set the driving shaft (16) into the attachment
(18).
Note:
Check whether the attachment (18) is set
properly, otherwise the processor lid (18) will not
close.
•
Put the geared lid (15) on the bowl (22).
•
Press the clamp (21) and turn the geared lid
(15) counterclockwise to the position “ ”,
release the clamp (21) and check the fixation
of the geared lid (15).
•
Put the motor unit (4) on the geared lid (15)
and turn it clockwise until fixing.
•
Insert the plug into the socket.
•
Set the required speed 1-20 using the con-
trol (1).
•
To switch the blender on press and hold the
button (2).
•
When the button (3) is pressed, the knife
rotates at maximal rotation speed.
•
Place the products into the lid chute (15), use
the pusher (14) for products feeding. Press
the pusher gently for products feeding.
•
After you finish using the unit, take the plug
out of the socket, disconnect the motor unit
(4) from the geared lid (15) by turning it coun-
terclockwise.
•
Then remove the geared lid (15) from the
bowl (22) by pressing the clamp (21) and
turning the lid clockwise.
•
Carefully remove the attachment (18).
•
Take the chopped products out of the pro-
cessing bowl (22).
•
Clean, wash and dry all the used parts imme-
diately after the end of operation.
CLEANING THE UNIT
•
After the end of operation or before cleaning
always switch the unit off and unplug it.
•
Clean, wash and dry all the used parts imme-
diately after the end of operation.
•
It is recommended to wash all removable
parts in warm water with neutral detergent.
You can wash the discs in the dishwasher.
•
For easy cleaning the cubic mesh (20), take
it out of the attachment (18) and remove the
remaining products with a pusher (13).
•
After processing of salty or sour products
rinse the used attachments with water imme-
diately.
•
Clean the motor unit (4) with a damp cloth.
•
Do not use coarse sponges, abrasives and
solvents to clean the unit.
•
Do not immerse the motor unit (4), whisk gear
(6), mash making attachment gear (8), chop-
per geared lid (10), processing bowl geared
VT-1480.indd 7
02.08.2012 15:15:41
