4
ENGLISH
Making juice
Before the first plugging in make sure that the
operating voltage of the unit corresponds to volt-
age of your mains.
Fruit and vegetables meant for processing must
be fresh.
Before juice extracting remove inedible parts
from vegetables or fruit, such as stems, hard peel
or stones, for example, cherry or peach.
Wash fruit/vegetables and chop them into pieces
easily fitting into the feeding chute (2).
–
Place the motor unit (9) on a dry, flat and
steady surface.
–
Before unit assembling make sure that the
operation modes switch is set in the posi-
tion «0», and the plug is not inserted into the
socket.
–
Set juice collector (6) on the motor unit (9).
–
Install mesh filter (5) in the juice collector (6).
–
Install grating filter (4) into the mesh filter (5).
Note: Do not use juice extractor if you found
mechanical damages of grating filter (4) or mesh
filter (5).
–
Install the lid (3) on the juice collector (6) and
fix it with by placing the locking arm (8) in ver-
tical position.
–
Install pulp container (11) in its place.
–
Open the juice cup (14) lid (12) and install the
separator (13) in it.
–
Put the juice cup (14) under the juice drain-
ing spout (7).
–
Insert the plug into the socket.
–
Switch juice extractor on by setting the switch
(10) to the position «I» (low speed) or to posi-
tion «II» (high speed).
Note:
Mode «I» (low speed) is intended for juice
extracting from soft vegetables/fruits - such
as tomatoes, ripe pears, strawberry, oranges,
plums, grapes, pumpkin, onion, cucumbers and
etc.
Mode «II» (high speed) is intended for juice
extracting from hard vegetables/fruits - such as
artichoke, carrot, apples, pepper, beets, pota-
toes, pineapples, vegetable marrows, celery,
spinach, dill, leek etc.
Attention! During processing of viscous or quite
hard foods in order to avoid the grating filter (4)
stopping and motor unit jamming it is recom-
mended to use the high speed «II» mode of juice
extractor operation.
–
The unit will switch on only if all the remov-
able parts are installed properly, and the lid
(3) is fixed with the locking arm (8).
–
Feed fruit/vegetable pieces into the lid (3)
feeding chute (2), only when grating filter (4)
is rotating.
–
Put vegetables or fruits cut beforehand grad-
ually into the lid (3) feeding chute (2) and
push them gently with the pusher (1). Do
not press on the pusher (1) too hard as it
can lead to decrease of juice amount as well
as to grating filter (4) rotation stopping. The
slower fruit and vegetables processing, the
higher juice extraction rate.
–
Do not put your fingers or any other foreign
objects into the lid (3) feeding chute (2).
–
During operation process check the grating
filter (4) and mesh filter (5) periodically for
obstruction of mesh with pulp, if necessary
wash the grating filter (4) and mesh filter (5),
switch juice extractor off and unplug it before
removing the filters.
–
Control the pulp container filling (11), if the
container (11) is filled up, switch juice extrac-
tor off, unplug it and remove the pulp from
the container (11).
ATTENTION
:
The maximal allowable con-
tinuous operation time is not more than 2
minutes with subsequent break of at least
3 minutes.
–
After unit operation, switch it off by set-
ting the switch (10) in the position «0», and
unplug it.
Cleaning and maintenance
After the end of operation or before cleaning
always switch juice extractor off and unplug it.
Disassemble and clean juice extractor after
every usage:
•
Remove the pusher (1) from the lid (3) feed-
ing chute (2).
•
Lower the locking arm and release the lid (3).
•
Remove the lid (3).
•
Remove juice collector (6) with the mesh fil-
ter (5) and grating filter (4).
–
It is recommended to wash all removable
parts in warm water with neutral detergent
right after unit operation.
–
It is more convenient to wash grating filter
(4) and mesh filter (5) slots from the outside
using a small brush.
VT-1614 IM.indd 4
14.03.2012 14:44:56
