Vitek VT-2342 Manual Instruction Download

Page: 4 / 32

ENGLISH

service or similar qualified personnel to avoid
danger.

•

Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction is
detected or after it was dropped, unplug the unit
and apply to any authorized service center from
the contact address list given in the warranty
certificate and on the website www.vitek.ru.

•

Transport the unit in the original package only.

•

Keep the unit out of reach of children and dis-
abled persons.

THE  UNIT  IS  INTENDED  FOR  HOUSEHOLD  USE
ONLY,  ITS  COMMERCIAL  USAGE  AND  USAGE
IN  PRODUCTION  AREAS  AND  WORK  SPACES  IS
PROHIBITED.

BEFORE THE FIRST USE

After unit transportation or storage at low tem-
perature keep it for at least three hours at room
temperature.
There may be water spots in the air humidifier,
this is normal, as the unit has undergone qual-
ity control.

–

Unpack the air humidifier, remove packaging
materials and any promo-stickers that can pre-
vent the unit operation. Check the unit for dam-
ages. Do not switch the air humidifier on in case
of damages.

–

Before plugging the unit in make sure that your
home mains voltage corresponds to the unit
operating voltage.

–

The unit is intended for operation in an AC power
network with the frequency of 50 Hz or 60 Hz, it
does not need any additional settings to operate
with the required nominal frequency.

Notes:

–

use the air humidifier at the room temperature
from +10°C to +40°C, and relative humidity less
than 80%.

–

water temperature should not 40°C.

USING THE AIR HUMIDIFIER

Notes:

–

the operation mode selection and setting but-
tons are sensory, you just need to touch the but-
ton to switch the necessary operation mode on,
every touch of the active button is accompanied
by a sound signal.

–

Remove the lid with nozzle (1).

–

Take the water tank (3) by the handle (2) and
remove it from the unit body (9).

–

Turn over the tank (3), open the lid (6) rotating it
counterclockwise.

–

Fill the tank (3) with necessary amount of water,
insert the lid (6) into the water inlet (4) and screw
it rotating it clockwise.

–

First place the filled water tank (3) back to its
place and then install the lid with nozzle (1).

–

Wait till the process chamber (7) is filled with
water.

Notes:

–

before the first use it is recommended to put
the mineral filter (5) into a container filled with
water of room temperature for several min-
utes.

–

remove the filter (5) from the lid (6) turning it
counterclockwise, put the filter (5) into a con-
tainer filled with water for several minutes, take
the filter out of the water and drain the remaining
water, then install it back on the lid (6), and turn
it clockwise as far as it will go.

–

Insert the plug of power cord into the socket,
you will hear a sound signal and the room tem-
perature and relative humidity digits (14) and
the symbols (17, 18) will appear on the control
panel (8).

Notes: - to choose the temperature measurement
units “C° or F°”, press and hold down the “ioniza-
tion” mode ON-button (19), you will hear a sound
signal, and the temperature measurement units will
change, the temperature measurement units are
shown by symbols (18).

–

Switch  the  unit  on  by  touching  the  on/off  but-
ton  (11) «ON/OFF», you will hear a sound signal,
the  unit  will  operate  at  minimum  mist  release
intensity, one mist release intensity symbol (21)
will light up.

–

To switch the air humidifier off, touch the but-
ton (11) «ON/OFF» again.

–

Unplug the unit.

Notes:

–

the humidity level readings may be slightly dif-
ferent from the readings of another hygrometer.

–

the humidity level readings depend on the room
air temperature.

–

draughts or other air flows may significantly
affect the air humidity and temperature read-
ings in the room.

OPERATION MODE CONTROL BUTTONS
On/off button «ON/OFF» (11)