Vitek VT-2346 Manual Instruction Download

Page: 5 / 32

ENGLISH

–

When the set time is reached the unit will be
switched off.

–

To switch the timer off, press the button (15)
until the light indicators (16) go out.

Night illumination
The  night  illumination  switches  on  automatically
when  you  switch  the  unit  on,  it  is  available  in  the
operating  modes  with  low,  medium  and  high  mist
release intensity.
In  normal  operating  mode  the  illumination  colors
change by rotation.

Not enough water

–

When the water tank (2) and the process cham-
ber (8) become empty, the unit will switch off.
The illumination will light up red.

–

Unplug the unit and remove the water tank (2).
Fill the tank (2) with water (see chapter «Using
the air humidifier»). Install the water tank (2)
filled with water on the humidifier body (9).

–

Switch the unit on for further operation.

CLEANING AND CARE
WARNING!
Always  switch  the  air  humidifier  off  before  clean-
ing,  disconnect  the  power  adapter  (13)  from  the
mains and remove the adapter cord connector from
the socket (11). Hard water causes appearance of
mineral  deposits  (scale)  in  the  process  chamber
(8) and in the water tank (2) that leads to improper
operation of the unit. To avoid it:

–

use  filtered  and  settled  water.  If  tap  water  is
hard,  it  is  recommended  to  mix  tap  water  with
distilled  water  in  proportion  1:1.  If  tap  water  is
too hard, mix it with distilled water in proportion
1:2 or use distilled water only.

–

Change water in the water tank (2) twice a week.

–

Thoroughly wash the process chamber (8) and
the water tank (2) with neutral detergent solu-
tion twice a week.

–

To clean the «sprayer» from the mineral deposit
(scale) (7) add 5-10 drops of detergent on it and
wait for approximately 10-15 minutes.

–

Remove the scale from the sprayer surface with
a soft brush, and then wash the process cham-
ber (8) with a neutral detergent solution.

–

Rinse the process chamber (8) several times.
Wipe the process chamber (8) with a soft cloth.

–

Clean the air humidifier body (9) with a soft,
slightly damp cloth, and then wipe it dry.

–

Clean the air inlet (4) and the air inlet grid (11)
on the unit body (9) bottom as it becomes
dirty.

–

To clean the float (5) remove it; to do this lift it
up and remove the left axis of the float from the
holder (6) groove, then remove the right axis.
Clean the float (5) from mineral scale.

–

Install the float (5) back to its place. To do it,
first insert the right axis of the float (5) into the
holder (6) opening and then insert the left axis
of the float (5) into the holder (6) groove. Make
sure that the float (5) axial movement (rotation)
is not hindered.

Notes:

–

do not immerse the air humidifier body into
water or other liquids;

–

do not use abrasives or solvents for cleaning the
sprayer (7);

–

you can use a descaling agent for kettles as a
detergent for the sprayer (7) and the float (5),
strictly following the instruction for this sub-
stance.

STORAGE

–

Pour the water out of the tank and make sure
that the process chamber and the sprayer are
dry before taking the unit away for storage.

–

Do not keep water inside the tank (2) or the pro-
cess chamber (8) of the unit.

–

Keep the air humidifier in a dry cool place away
from children and disabled persons.

TROUBLESHOOTING

Problem

Possible causes

Troubleshooting

No “mist”