5
ENGLISH
Attention! Do not allow children to play
with polyethylene bags or packaging film.
Danger of suffocation!
•
If the power cord is damaged, it should
be replaced by the manufacturer, a
maintenance service or similar qualified
personnel to avoid danger.
•
Do not attempt to repair the unit. Do not
disassemble the unit by yourself, if any
malfunction is detected or after it was
dropped, unplug the unit and apply to any
authorized service center from the con-
tact address list given in the warranty cer-
tificate and on the website www.vitek.ru.
•
To avoid damages, transport the unit in
the original package only.
•
Keep the unit in a dry cool place out
of reach of children and disabled per-
sons.
THE UNIT IS INTENDED FOR HOUSEHOLD
USE ONLY, ITS COMMERCIAL USAGE AND
USAGE IN PRODUCTION AREAS AND
WORK SPACES IS PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage
at low temperature keep it for at least
three hours at room temperature
before switching on.
–
Unpack the unit completely and remove
any advertisement stickers that can
prevent the unit operation.
–
Check the unit for damages; do not use
it in case of damages.
–
Before connecting the power adapt-
er, make sure that voltage of the
mains corresponds to unit operating
voltage.
–
Charge the battery and lubricate the
blade block following the recommen-
dations below.
The hair clipper can operate only on
the built-in rechargeable battery.
Battery charging
Full charging of the accumulator battery
is enough approximately for 35 minutes of
continuous operation.
–
Switch the hair clipper off, setting the
power switch (3) to the “O” position.
–
Insert the power adapter (11) cord plug
into the connection socket (1) on the
lower side of the unit body.
–
Place the hair clipper on a flat stable
surface.
–
Plug the power adapter (11) plug into
the mains socket, the charging indica-
tor (2) will light.
–
The full charging time for the accu-
mulator battery is 10-12 hours; do not
exceed it to avoid reducing the battery
operating life.
–
After the battery is charged, unplug
the power adapter (11) from the mains,
remove the adapter cord plug from the
connection socket (1), the charging
indicator (2) will go out.
Attention:
–
Strictly follow the sequence of oper-
ations when connecting the power
adapter. First connect the power
adapter jack to the socket (1) and
then connect the power adapter
plug (11) to the mains socket.
–
Charge the battery the first
2-3 times for 10-12 hours. The fol-
lowing charging cycles time should
not exceed 8 hours.
–
To prolong the battery operating
life, it should be discharged com-
pletely before each charging cycle.
–
Do not charge the batteries at tem-
perature below +5°C and above +35°C.
–
If you have not used the hair clipper
for a month or more, charge it com-
pletely before use.
–
Never leave the unit connected to
the mains unattended.
IM VT-2578.indd 5
6/11/20 5:31 PM
Summary of Contents for VT-2578
