background image

EN

27

However, if you use an extension, you 

should take some precautions, such as:

� If using this machine outdoors, use 

only suitable extension cords for 

outdoor use. Using a proper extension 

cord reduces de risk of electric shock;

� Use only extension cords with 3 

cables, plugs and sockets with earth 

connection; 

� The extension cable section must be 

proportional to the length and have 

equal or higher characteristics to the 

compressor’s power cord;

� Do not use damaged extension cords. 

Check them before using and replace 

if necessary;

� When it’s an extension cord reel, unroll 

the entire cable;

� Always unplug the extension cord 

before removing the equipment’s 

power cable;

2.3 - BEFORE OPERATING

Make sure that this tool is only used 

by who is familiar with the instruction 

manual.

To ensure a safe operation, you must:

� Check the entire equipment before 

using it. Check that all the accessories 

are correctly assembled and attached 

to the machine and in good conditions. 

Never use damaged accessories;

� In a regular operation, the tool was 

conceived to produce vibrations. Verify 

if every fixing screw is well tightened. 

It is important a regular inspection in a 

way to ensure the safety questions and 

the machine’s performance. 

� Verify if there are any misalignments 

in the moving parts or any condition 

that may affect its normal operation. All 

moving parts must spin softly, without 

abnormal noises and sparks in the 

brushes;

� Check if the safety devices are 

in perfect conditions and working 

correctly. Never use the machine if 

any safety device is missing, inhibited, 

damaged or worn;

� Ensure that the switch is off when you 

plug in the power cable. If the switch is 

damaged or does not allow controlling 

the demolition hammer, it must be 

repaired or replaced in a way to avoid 

a sudden start. 

Perform all the needed adjustments 

and in case of doubts ask your 

distributor for assistance. 

2.4 - WHILE OPERATING

Keep other people away from 

the working area. Never use the 

tool if animals or people, particularly 

children, are nearby.

Keep the working area clean, organized 

and well illuminated (brightness from 

250 to 300 lux), in order to reduce 

the risk of accidents. 

Always wear personal protective 

equipment. Wearing safety goggles, 

safety masks, ear protection, non-slip 

safety footwear, long sleeve clothing, 

gloves and helmet under proper 

conditions reduces the risk of injuries. 

The clothing worn while operating the 

tool must be appropriate and tight, 

such as a work coverall. Do not wear 

loose clothing or jewellery. Keep hair, 

clothing and gloves away from the 

moving parts.

A massive load of vibrations may 

damage nervous and circulatory 

systems to whom have circulatory 

problems. Inform your doctor if any 

symptoms arise caused by vibration. 

Among these symptoms, that occur 

particularly on fingers, hands and 

wrists, is also included loss of 

sensation, pain, muscle weakness, skin 

discoloration or tingling sensation.   

While operating the machine, schedule 

some time to rest and avoid using it 

for long periods of time. Permanent 

vibration is very harmful.  

The control and safety devices installed 

in the machine must not be removed or 

inhibited.

To ensure a safe operation, you must:

� When using the machine, place 

yourself in a stable position and well 

balanced. Hold the equipment firmly 

with both hands to ensure a continuous 

operation and to withstand unexpected 

situations, such as a kickback.

� Make sure that the ventilation openings 

are not blocked while operating the 

machine. Do not place any objects over 

the grids. 

� The tools (drills, point chisels, chisels) 

and the insertion support may overheat 

while operating. It might burn the user. 

Wear protection gloves every time the 

drilling tool is being replaced. 

� Make sure that you don’t damage the 

electrical circuits, gas and water pipes 

when operating the equipment. Any 

of these damages may cause fires, 

explosions, electrical shocks or several 

expensive losses.   

� Avoid using the machine on surfaces 

coated with paints containing lead or 

other materials harmful to health. Any 

contact or inhalation of dust may cause 

allergic reactions and / or breathing 

diseases. Wear a mask and work with 

a dust extraction device if the machine 

allows it.

� Materials containing asbestos cannot 

be worked. Asbestos is carcinogenic.

2.5 - MAINTENANCE 

AND CLEANING 

Before cleaning, adjusting, repairing 

and maintenance works, the power 

cable must be unplugged.

Replace worn or damaged parts 

immediately, so that the machine is 

always in a safe operating condition.

Summary of Contents for Pro-Power VIMP1500













































Reviews: