background image

 

18

7.7 Pull starter Fly100evo

 

 

A first control of the components of the pull starter is recommended to 25 hours.   
Just removed the manual starting from the plate, the hooks/splines will be visible.   
Verify the conditions and the slide of the hooks, lifting them with a finger. In every case 
add some oil (for rusted bolts) on the pivots of sliding.   
The manual starting: as first operation loosen the knot that stop the handle of starting 
and unthread the rope from the eyelet drives, suitable in figure 1.   
Now positioning the rope in the hollow of the pulley as shown in figure 2, rotate the 
pulley of wrapping clockwise, to lose the tension given by the spooling spring.   
Unscrew the central bolt of 6mm, figure 3.   
Lift the pulley with the help of a small screwdriver holding back the spooling spring that 
is found under the pulley, figure 4 (you will avoid to go out this spring). If for distraction 
or accident the spooling spring escapes, can be rearranged (provided of patience) 
manually in the original position.   
In the figure 5, freed the pulley, is shown the spooling spring.   
Assemblage: add grease to the spooling spring and the pivot where slides the pulley, 
then insert the pulley in the pivot drives.   
Tight the screw of 6 mms, inserting lock-tight of medium resistance (if the washer 
creates attrition with the pulley, turn upside-down the washer).   
Position the rope in the hollow as in figure 2; turn the rope in the pulley wrapping, up to 
fill it.   
Always maintaining the rope in the hollow, rotating counterclockwise unitill the origin of 
the tension of the spooling spring begin; from this position rotate counterclockwise the 
pulley of two complete turns, then maintain this position (hold the pulley) and return to 
insert the rope in the eyelet drive, as in figure 1.   
Finally always holding the pulley mark the rope with a pen in the adjacent zone the 
structure, picture 6. Once made the sign, free the pulley and you can leave also the rope 
reenters in the wrapping.    
If necessary, for the remainder installation returned to the indications of the paragraph 
3.8 

 

 

7.7 / pull starter Fly100evo 

 

Summary of Contents for Easy100































Reviews: