background image

2

PACKAGE CONTENTS

WARNING!

(x1)

Base

B

 (x4)

Caster

C

 (x2)

Base Pole

(x1)

Rear Cover

(x2)

VESA 

Extension 

K

 (x2)

VESA 

Extension

(x4)

Cable Cover

H

 (x1)

Mounting 

Plate

(x2)

Upper Pole

(x1)

Equipment 

Shelf

(x2)

Shelf Mounting 

Bracket

(x1)

Front Cover

If you do not understand these directions, or if you have any doubts about the safety of the installation, 

please call a qualified technician. Check carefully to make sure there are no missing or defective parts. 

Improper installation may cause damage or serious injury. Do not use this product for any purpose that is 

not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or 

injury caused by improper mounting, incorrect assembly or inappropriate use.

NOTE: 

SOME HARDWARE INCLUDED MAY NOT BE USED

(x8)

M6x8

M

 (x8)

M8x20

(x16)

M6x12

(x1)

4mm Allen 

Wrench

W

 (x1)

5mm Allen 

Wrench

(x1)

6mm Wrench

M-A

 (x4)

M5x14

(x5)

Cable Tie

M-B 

(x4)

M6x14

M-C

 (x4)

M6x30

M-D 

(x4)

M8x30

M-E 

(x4)

M8x50

M-G 

(x8)

5mm Spacer

M-H

 (x8)

15mm Spacer

(x1)

M6x18

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

154lbs

(70kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

11 lbs

(5 kg)

TV

DVD SHELF

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• 

NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV CART.

• 

USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

M-F 

(x4)

Washer

Q

 (x8)

M8x8

(x5)

Cable Tie 

Holder

(x1)

10mm Wrench

Summary of Contents for STAND-TV02PW









Reviews: