2
3
ASSEMBLY STEPS
STEP 1
OPTION 1: Weighted Base
Install the Pole
(a)
to the Weighted Base
(b)
using
M5x14 Bolts
(e)
, and tighten using the Allen Key
(m)
.
Optionally, you can drill a 10mm diameter hole in
your desk and secure using the Support Plate
(h)
, M10
Washer
(i)
, Spring Washer
(j)
and M10 Bolt
(g)
. Fasten
the M10 Bolt with provided Wrench
(n)
.
PACKAGE CONTENTS
TOOLS NEEDED
WARNING!
Phillips
Screwdriver
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE:
NOT ALL HARDWARE INCLUDED WILL BE USED
d
(x2)
VESA Plate
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
•
NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF STAND
•
USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
c
(x1)
Swivel Arm
a
(x1)
Pole
e
(x4)
M5x14
l1
(x1)
Wire Clip
k
(x1)
Grommet Base
Plate
j
(x1)
Spring Washer
i
(x1)
M10 Washer
f
(x2)
Nut
b
(x1)
Weighted Base
g
(x1)
M10 Bolt
h
(x1)
Support Plate
o
(x8)
M4x12
n
(x1)
Wrench
m
(x1)
Allen Key
l2
(x4)
Wire Clip
r
(x1)
Soft Pad
q
(x4)
M4 Spacer
OPTION 2: Existing Grommet Base
If the existing grommet hole comes with a plastic
protector, remove it to ensure a flat surface before
installing the desk mount. Install the Grommet
Base Plate
(k)
to the Pole
(a)
using M5x14 Bolts
(e)
, and tighten using the Allen Key
(m)
. Attach
Soft Pad
(r)
to the Grommet Base Plate
(k)
.
Position the Pole
(a)
on the mounting surface and
secure using the Support Plate
(h)
, M10 Washer
(i)
, Spring Washer
(j)
and M10 Bolt
(g)
. Fasten the
M10 Bolt using provided Wrench
(n)
.
OPTION 3: Self-Drilled Grommet Base
Position the Pole
(a)
on the mounting surface and
mark the center hole. Drill a 3/8" (10mm) diameter
hole at the marked position through the mounting
surface. Install the Grommet Base Plate
(k)
to
the Pole
(a)
using M5x14 Bolts
(e)
, and tighten
using the Allen Key
(m)
. Attach Soft Pad
(r)
to the
Grommet Base Plate
(k)
. Position the Pole
(a)
on
the mounting surface and secure using the Support
Plate
(h)
, M10 Washer
(i)
, Spring Washer
(j)
and
M10 Bolt
(g)
. Fasten the M10 Bolt using provided
Wrench
(n)
.
Drill
p
(x8)
M4x30
a
e
b
h
g
i
l
j
Figure 2
h
g
i
j
a
k
e
Figure 3
Figure 5
r
Figure 4
h
g
i
j
k
a
e
Figure 6
Figure 8
r
Figure 7
22 lbs
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
