background image

VZN T5 SERIES

10

P/N 1011066 Rev. G 12/13

CAUTION

Due to its weight and size, the VZN system MUST be 

mounted with the provided Mounting Bracket. Read 

the Mounting the System section before attempting to 

mount the VZN system. Use care when lifting heavy 

objects.

Mounting the System

NOTE: Use caution when lifting and mounting the sys-

tem. The system MUST be mounted using the provided 

Mounting Bracket.

The VZN system comes with a Mounting Bracket. When 

mounting the system, pay attention to the following guidelines:

•  • 

Allow sufficient access for cartridge replacement. 

VZN-421 units should be mounted with 20 inches to the 

left or right. VZN-441 units should be mounted with 40 

inches to the left or right.

•  • 

Mount the system near but NOT above an appropri-

ate electrical outlet.

•  • 

Mount the system near a drain for flushing opera-

tions.

•  • 

Mount the system before all consumable water  

filtration processes.

•  • 

Mount the system with the provided Mounting 

Bracket and hardware capable of supporting 120 lbs. or 

more.

•  • 

Secure the Mounting Bracket into wall studs or with 

the appropriate heavy duty mounting hardware.

The system is pre-assembled to a Back Plate. The Back Plate 

has mounting holes across the bottom portion to secure the 

bottom of the system to the wall. Some of the bottom mount-

INSTALLATION (continued)

ing holes may be obscured. Plan your mounting accordingly.

 

Follow these steps to secure the Mounting Bracket to the wall 

and seat the VZN system:

  1.  Use a stud finder and level to attach the Mounting 

Bracket securely to the wall with the appropriate  

mounting hardware (Figure 2).

  2.  The Mounting Bracket is designed so that the VZN  

system can be lifted and hung on the Mounting Bracket. 

With assistance, lift the system and seat it onto the 

Mounting Bracket securely (Figure 2).

  3.  Secure the bottom portion of the VZN system to the 

wall using the holes provided. Make sure the mounting 

hardware secures the system into wall studs or use the 

appropriate mounting hardware.

  4.  Screw the Carbon Element Housing onto the Carbon 

Element Head without the Carbon Element installed.

NOTE: Do NOT install the Carbon Element at this time. 

The Carbon Element should only be installed after the 

Ultra Filter Cartridge has been rinsed.

  5.  Screw the TAC Housing onto the TAC Head without the 

TAC Cartridge installed.

NOTE: Do NOT install the TAC Cartridge at this time. The 

TAC Cartridge should only be installed after the Ultra 

Filter Cartridge has been rinsed.

Secure Mounting Bracket

to wall studs using

appropriate hardware.

The system is

designed to hang from

the Mounting Bracket.

Back Plate

(holes along bottom 

for additional 

mounting stability)

Figure 2. Mounting the System

Summary of Contents for VZN-421H-T5

























Reviews: