background image

VZN T5 SERIES

12

P/N 1011066 Rev. G 12/13

INSTALLATION (continued)

CAUTION

Do NOT use the Rinse Valve for consumable water.

3/4”

 Garden

Hose

Connection

3/4”

Garden Hose

(not supplied)

directed

to drain

Rinse Valve Connection

Inlet

Ball Valve

(Manual)

Outlet

Ball Valve

(Manual)

Figure 5. Rinse Valve Connection

Figure 6. Inlet and Outlet Connections

Rinse Valve Connection

  1.  Obtain a length of 3/4” garden hose long enough to 

reach from the Rinse Valve to the drain. 

  2.  Install a gasket in the end of the hose (non-drain end).

  3.  Connect the hose to the Rinse Valve fitting. Use a back-

up wrench on the fitting if required (Figure 5).

  4.  Direct the other end of the hose to the drain. Secure as 

necessary.

NOTE: The drain MUST accommodate a flow of up to  

15 gpm.

System Inlet Connection

The System Inlet has a 3/4” NPT male thread at the Inlet 

Valve (Figure 6). Do NOT overtighten fittings as this could 

cause the plastic ball valve to crack.

Use plastic fittings and a pipe thread sealant approved for use 

on PVC fittings when making connections.

Filtered Water Permeate Outlet Connection

The System Outlet has a 3/4” NPT male thread at the Outlet 

Valve (Figure 6). Do NOT overtighten fittings as this could 

cause the plastic ball valve to crack.

Use plastic fittings and a pipe thread sealant approved for use 

on PVC fittings when making connections.

Inlet Water Plumbing

The "T" Fitting with plug (supplied) should be installed at the 

System Inlet. This fitting will be used for sanitizing the system 

and downstream plumbing (Figure 6a).
Before connecting the fitting to the System Inlet, the plumb-

ing to the system must be flushed clear of all debris. Hold a 

bucket at the inlet water line and slowly open the Inlet Water 

Valve. Allow the pipe to flush until all debris is removed.

Inlet Ball 

Valve

Sanitation  

Plug

T-Fitting 

(not supplied)

Inlet

Figure 6a. Installing a T-Fitting for Sanitizing

Summary of Contents for VZN-421H-T5

























Reviews: