background image

Page 2 

TR001 DEFENDER™

  

www.vogelzang.com

 

VGZ-026 / 20120306.0

1.  The installation of this stove must comply with your 

local building code rulings. Please observe the clear-
ances to combustibles (see reference figures 1–3). 
Do not place fuel, furniture or any other objects within 
the clearance area.

2.  Verify that the stove is properly assembled and 

installed before firing the stove for the first time. 
After reading these instructions, if you have any 
doubt about your ability to complete your installation  
properly, you must obtain the services of a  
professional licensed installer familiar with all  
aspects of safe and correct installation.  DO NOT  
use temporar y or makeshift compromises  
during installation. There must be 

NO DEVIATION 

OR ALTERATION OF ANY KIND from the very spe-
cific instructions spelled out in this instruction manual 
as it pertains to the installation of this woodstove. 

 

NO EXCEPTIONS!

3.  DO NOT store wood, kindling, flammable liquids 

or other combustible materials in the vicinity of the 
appliance. Refer to certification label on back of unit 
and reference figures1–3 in this manual.

4. 

DO NOT INSTALL THIS STOVE IN A MOBILE 
HOME, MANUFACTURED HOME, TRAILER OR 
TENT NO EXCEPTIONS! (HUD Federal Standard: 
24 CFR Ch.XX).

5. 

DO NOT ELEVATE THIS STOVE BY ANY MEANS. 
(i.e. bricks under legs, cement blocks)  Stove legs 
must set directly upon the solid-surface non-com-
bustible floor as specified in this stove instruction 
manual. 

6. 

DO NOT MODIFY THIS STOVE IN ANY WAY!  
Stove must be installed with legs and heat shield 
provided, attached as shown in the instructions. 
DO NOT OPERATE WITH DOOR OPEN EXCEPT 
WHEN LOADING FUEL
. Assemble only with origi-
nal parts as supplied and shown in this manual. 

DO 

NOT OPERATE A STOVE THAT IS MISSING ANY 
PARTS!
 If any parts are missing or defective, please 
notify the dealer or manufacturer immediately. Re-
place missing, broken or worn parts with factory 
original or equivalent parts only.

7. 

CAUTION: DO NOT ALTER COMBUSTION AIR 
CONTROL RANGE TO INCREASE FIRING OR 
FOR ANY REASON. 
Altering or tampering with air 
control beyond normal capacity will create unsafe 
and hazardous conditions.

8.  Always connect this stove to a chimney and vent to 

the outside. Never vent to a room or inside a building. 
DO NOT CONNECT THIS UNIT TO A CHIMNEY 
FLUE SERVING ANOTHER APPLIANCE.

9. 

DO NOT CONNECT A WOOD BURNING STOVE 

TO AN ALUMINUM TYPE B GAS VENT. This is 
not safe. Use approved masonry or an Underwrit-
ers Laboratories Listed UL 103 HT (US)/ULC-S629 
(CDN) Residential Type and Building Heating Ap-
pliance Chimney. Use a 6˝/152mm diameter chim-
ney, that is high enough to give a good draft. (See  
specifics in Chimney Connections instructions).

10.  Be sure that your chimney is safely constructed and 

in good repair. Have the chimney inspected by the fire 
department or a qualified inspector. Your insurance 
company should be able to recommend a qualified 
inspector. Chimney connector pipe must be in good 
condition. Replace if necessary before using stove.

11.  Creosote or soot may build up in the chimney con-

nector and chimney and cause a house/building 
fire. Inspect the chimney connector and chimney 
twice monthly during the heating season and clean 
if necessary. (see Service Hints). 

12.  In the event of a chimney fire, turn the air controls to 

closed positions, leave the building and 

CALL THE 

FIRE DEPARTMENT IMMEDIATELY!  Have a clearly 
understood plan on how to handle a chimney fire by 
contacting your local fire authority for information 
on proper procedures in the event of a chimney fire.  
After the fire is out, the chimney must be cleaned 
and inspected for any stress or cracks before starting 
another fire. Check the condition of any combustibles 
surrounding the chimney.

13.  Ashes should not be allowed to accumulate above 

the top of the lower primary air orifice (LPAO, air vent 
at front of firebox, just inside of door).

14. 

DISPOSAL OF ASHES

 

Ashes should be placed in a steel container with 
a tight fitting lid and moved outdoors immediately. 
The closed container of ashes should be placed 
on a noncombustible floor or on the ground, well 
away from all combustible materials, pending final 
disposal. If the ashes are disposed of by burial in 
soil or otherwise locally dispersed, they should be 
retained in the closed container until all cinders have 
completely cooled. Other waste shall not be placed 
in this container.

15.  To prevent injury, do not allow anyone to use this 

stove who is unfamiliar with the correct operation of 
the stove.

16.  Do not operate stove while under the influence of 

drugs or alcohol.

17. 

DO NOT ELEVATE THE FIRE. Build fire directly on 
the bottom of the firebox. This stove has not been 
tested with the use of grates, andirons or other means 
of elevating the fire and must not be used.

SAFETY INSTRUCTIONS-Read All Instructions Carefully.

Summary of Contents for DEFENDER TR001





















Reviews: