8
Connector pipe is used to make the connection
from the
ſPCN
positioning of your stove to an approved
chimney. Connector pipe is
NOT
KPENWFGF
as part of
the stove. Connector pipe must be 6”/152mm diameter
minimum of 24 MSG (minimum standard gauge) b
NC
ck
or 26 MSG b
NWG UVGGN
stove pipe. Any connector pipe
used must be in good condition.
4GRNCEG
if necessary
before using stove. Connector pipe is not rated to pro-
vide
ENQUG
contact to combustib
NG
mater
KCNU
and must
have proper
ENGC
rance from combustib
NG
mater
KCN
s
as shown in the
ENGC
rance diagrams on the previous
pages. Connector pipe
UJQWNF
never be used in
RNCEG
of a chimney. If proper
ENGC
rances are not observed a
JQWUGſTGEQWNFTGUWNV
INSTALLATION INSTRUCTIONS
Please Note:
Insta
NN
ation of a
ƀ
ue damper is NOT
recommended.
Combustion co
PVTQN
is regu
NC
ted by the
intake of combustion air, not the exhaust.
1. The crimped end of the stovepipe
ſVU
inside the
stove
ƀWG EQNNC
r. Secure with three (3) sheet
OGVCN
screws. The
ſTUV
section of connector pipe must be
UKPING
w
CNNGF
to proper
N[
attach to the stove
EQNNC
r.
+PUVCNN CFFKVKQPCN
pipe and
GND
ow with the crimped
end towards the stove. This
YKNN CNN
ow any conden-
UCVKQPKPVJGƀWGVQ
run bac
MKPVQVJGſTGD
ox.
2. Horizont
CN
pipe runs must
UNQRG
upwards
towards the chimney at
NGCUV ŊOO
per foot
of horiz
QPVCN
run.
3. Yo u mu s t h ave a t
N G C U V Ŋ
/ 4 5 7 m m o f
ENGC
rance between any horiz
QPVCN
piping and the
EGKNKPI
4. The pipe cannot extend into the chimney
HN
ue
ſIWTG
5. Secure
RKRGGND
ow sections with three equ
CNN
y
spaced sheet
OGVCN
screws at each joint to make
the piping rigid. DO NOT CONNECT THIS STOVE
TO ANY AIR DISTRIBUTION OR DUCT SYSTEM.
6. It is recommended that no more than two (2)
u
bends be used in the stovepipe insta
NN
a-
tion. The use of more than two
0
u
bends may
decrease the amount of draw and possib
N
y
cause smoke
URKNNCI
e. Where possib
N
e, use
QPN[
corrugated (non adjustab
NG
e
ND
ows. These
pro
XKFGCDGVVGTUGCN
7. The connector pipe must not pass through an
attic or roof space, trusses, c
N
oset, or any c
QPEGCNG
d
space,
ƀQQ
r,
EGKNKPI
w
CNN
or combustib
NG
construc-
tion. (See Chimney Connector Systems &
%NGCT
-
ances, page 13.) A manufactured chimney system
NKUVGF
to UL 103 HT
757.%5
(CDN) must
be used from the
ſTUV
penetration of
EGKNKPI
or w
CNN
to the chimney cap.
Where passage through a w
CNN
or partition of com-
bustib
NG
construction is desired, the inst
CNN
ation sh
CNN
conform to NFPA 211 (USA) or CAN/CSA-B365
(Canada).
WARNING: DO NOT USE SINGLE WALL CON-
NECTOR PIPE AS A CHIMNEY - A HOUSE FIRE
COULD RESULT.
Figure 9 – Stovepipe/Flue Connections
NOTE: CONNECTOR PIPE IS
NOT INCLUDED
.
TO PURCHASE, VISIT YOUR LOCAL HARD-
WARE, HOME, OR BUILDING CENTER.
SEE “LOCATING STOVE” PAGE 6 FOR
ADDITIONAL SPECIFICATIONS.
CONNECTOR PIPE INSTALLATION
