background image

INSTALLATION 

WALL DRILLING AND BRACKET FIXING 

Please read the instructions carefully.

Unpack the canopy and check that all functions are working. Ensure
that the voltage (V) and the frequency (Hz) indicated on the serial plate match the voltage

and frequency at the installation site.

Check that the area behind the installation surface to be drilled is clear
of any electrical cables or pipes, etc.

The stainless steel and glass surfaces of the canopy are very easily
damaged during installation if grazed or knocked by tools. Please take care to protect
the surfaces during installation.

Protect the cooktop surface below with cardboard, or the like, to
prevent damage occurring whilst the wall canopy is being installed above.

The manufacturer shall not be liable for failure to observe all safety
regulations in force for the correct and normal operation of electrical parts.

Choose a ven

ti

ng mode: 

Ex

tr

ac

ti

on-air mode 

Recircula

ti

on mode 

Venti

ng knob pos

iti

on

Extrac

ti

on-air mode: Turn 

the ve

nti

ng knob here 

means ven

ti

ng outside 

Circula

ti

ng-air mode: 

Turn the ven

ti

ng knob 

here means recircula

ti

on 

5

Summary of Contents for 330171













Reviews: