DC5V
AUX
USB
TF
Please fully charge the Barrel Speaker before using it for the
first time.
Connect the USB A end of the Charging Cable to a USB Charging
Port and insert the Micro USB end to the port on the Barrel. Make
sure it is properly connected. The red indicator light will be lit while
the Barrel is charging. When the battery is full, the red indicator
light will switch off automatically.
To turn on, press the Power Button. The speaker will play the
start-up audio tone. To turn off, press the Power Button.
The Power Button and the Mode Button will blink repeatedly
with a white light when the Barrel is powered on.
Pairing with Bluetooth Devices
Your speaker must be paired to a Bluetooth device before it can
be used. It is only necessary to pair your speaker once with each
device.
1. Open the Bluetooth Menu on the device you wish to pair. Some
devices require you to select Search for devices or Add new
device in order to create a Bluetooth pairing.
2. With the speaker turned off press the Power Button.
Navigate to Bluetooth Mode by pressing the Bluetooth
Button. If the speaker is not already in Bluetooth Mode,
the speaker will play a pairing voice prompt while awaiting a
Bluetooth connection.
IDENTIFYING PARTS
CHARGING
INSTRUCTION MANUAL
Please read and retain these instructions for future reference.
• Bluetooth
• Speakerphone
• Aux Input
• SD Card Input
• USB Input
• FM Radio
• Passive Woofers
• Up to 6 Hours Playtime
• 35 W Peak Power
• Volkano Barrel Series Bluetooth Speaker
• USB Charging Cable
• Instruction Manual
• Aux Cable
• Shoulder Strap
HIGHLIGHTS
INSTRUCTIONS FOR USE
Barrel Series
FABRIC
SPEAKER
1. Micro USB Charging Port
2. Aux Input
3. USB Port
4. Micro SD Card Slot
5. LED Indicator Light (Charging)
6. Bluetooth Button
7. Previous Song / Previous Station / Volume Down Button
8. Power Button
9. Mode Button
10. Next Song / Next Station / Volume Up Button
11. LED Indicator Light (Power)
12. Play / Pause / Answer Call / Auto Scan Button
2
3
4
VK-3410
PACKAGE CONTENTS
5
SPECIFICATIONS
Bluetooth:
Version:
4.2
Chipset:
JL
Profiles:
HFP / HSP / A2DP / AVR
Range:
10
m
Sensitivity:
85 dB
Charge Input:
5 V DC, 1 A
Power:
2 x 12W = 24 W RMS / 35 W Peak
Battery Capacity:
3 600 mAh
Charge Time:
4 – 6 hours
Battery Type:
Lithium-Ion
Playback Time:
4 – 6 hours
Maximum Size for USB Drive: 64 GB
Driver:
2 x 3
″
Impedance:
4 Ω
Signal to Noise Ratio:
90 dB
Frequency Response:
80 Hz – 20 kHz
FM Radio Range:
87.5 – 108.8 MHz
5
1
2
4
3
6
7
8
9
10
11
12
6
3. Wait until you see “Barrel” on your device screen.
4. Select “Barrel” on your device and follow any further prompts
to pair. Once pairing is complete, the speaker will play a short
tone and will be ready to play audio via Bluetooth. The blue
indicator light will blink at a slower rate when pairing is complete.
Note
: If you are unsure on how to access your Bluetooth
menu on
your device, please refer to your device’s instruction manual.
Locating the Bluetooth Menu
iPhone, iPad, and iPod Touch
a) On your device, go to Settings.
b) Select Bluetooth. If Bluetooth
is not on, turn it on.
c) The iPhone / iPad / iPod will automatically search for new devices
Android™ Phones and Tablets
a) On your device, go to the Settings Menu.
b) Select Bluetooth (on older Android devices Bluetooth is
found in the Wireless & Networks Menu). If Bluetooth is not
on, turn it on.
c) Select “Search for devices” if your phone or tablet does not
automatically search for new devices.
Connecting with Paired Devices
Once the speaker is switched on, it will automatically connect with
the last paired Bluetooth device that is on and within range. If the
speaker does not connect automatically, open the Bluetooth Menu
on your device and select “Barrel” from the Bluetooth device list.
7
Android™ Phones and Tablets
a) On your device, go to the Settings Menu.
b) Select Bluetooth (on older Android devices Bluetooth is
found in the Wireless & Networks Menu). If Bluetooth is not
on, turn it on.
c) Select “Search for devices” if your phone or tablet does not
automatically search for new devices.
Connecting with Paired Devices
Once the speaker is switched on, it will automatically connect with
the last paired Bluetooth device that is on and within range. If the
speaker does not connect automatically, open the Bluetooth Menu
on your device and select “Barrel” from the Bluetooth device list.
Controls
Function
Operation
Increase Volume
Long press the Next Song
/ Next Station / Volume Up
Button
Decrease Volume
Long press the Previous
Song / Previous Station /
Volume Down Button
Navigate to Next Track
Short press the Next Song
/ Next Station / Volume Up
Button
Navigate to Previous Track
Short press the Previous
Song / Previous Station /
Volume Down Button
To navigate between the USB, Micro SD, Bluetooth and Aux Modes
short press the Mode button.
