3
30
22
23
24
25
26
27
28
29
A
B
C
31
32
33
Zanussi supply a range of cleaners with different accessories, all of which are covered in this manual. Please refer to your
specific model and its accessories.
INSTRUCTIONS FOR USE
•
Before placing into operation make certain that the
filters are in the proper position and check that the
dust container is in place.
•
To connect the hose into the suction inlet push it until
it clicks. To disconnect the hose form the suction inlet,
push the button at the end of the hose. (Refer to the
diagram on page 4, reference 33)
•
Attach the telescopic tube to the hose handle and floor
nozzle by pushing and twisting together. (Twist and pull
apart to dismantle).
A.
Unwind a sufficient length of cable and insert the plug
into the powersocket. A YELLOW mark on the power
cable shows the ideal cable length. Do not extend the
cable beyond the RED mark.
B.
Press the ON/OFF button to switch the appliance on. On
initial start up full power is reached after approximately
1-2 seconds .
C.
Extend the cable and connect to the mains. The
cleaner is fitted with cord rewind, ensure cord is
not twisted before use. (Press foot pedal to rewind.
Note: Please hold the plug to prevent it striking
you or the machine).
Sound level: 82,5 db(A)
GETTING THE BEST RESULTS
Carpets:
Use the floor nozzle with the lever in horizontal
position.
Hard Floors:
Use the floor nozzle with the lever in vertical
position.
Loose rugs/curtains/light weight fabrics:
Use the floor
nozzle for loose rugs and the upholstery nozzle for curtains,
cushions etc.
Confined areas:
Use the crevice nozzle for crevices, corners
and radiators.
Dusting brush -
Use for removal of dust coverage on
furniture and slatted blinds.
MAINTENANCE
REMOVING THE CONTENTS OF THE DUST CONTAINER
•
Never operate the cleaner without the dust container
installed.
•
Your cleaner is fitted with an electronic filter indicator.
The dust container must be emptied if the window of
the electronic filter indicator is illuminated when the
cleaner is operating at maximum power and the nozzle
is raised from the floor.
•
Please note: It is normal for the red light of the indicator
to flicker on and off during use . If the dust container
is emptied and the indicator is still active, it means
that the cartridge filter is clogged. In this case, follow
the instructions of chapter ‘Replacing or cleaning the
cartridge filter’.
22
Remove the dust container by pushing the open
buttons on the two sides of the dust container handle.
23
Remove the contents of the dust container by pushing
the orange - coloured opening button.
24,25
If necessary, the protector mesh also can be removed
(24) in order to shake the dirt from its surface (25).
26
Close the dust container lid until it clicks.
22
Insert the dust container back into the cleaner by
pressing it down until it clicks
REPLACING THE FILTERS
Filters should be replaced at least twice a year or when they
become visibly soiled. Always operate the cleaner with filters
installed to avoid reduced suction.
Disconnect from electrical outlet before changing the filters.
Menalux branded filters are strongly recommended by Volta.
Those high quality filters will ensure a long life time of your
Volta vacuum cleaner. For more information about Menalux
products, please visit our web site: www.menalux.com.au.
REPLACING OR CLEANING THE CARTRIDGE FILTER
22
Remove the dust container by pushing the open
buttons on the two sides of the dust container handle.
23
Remove the contents of the dust container by pushing
the orange - coloured opening button.
24
Remove the protector mesh.
27
Remove the cartridge filter by turning it
counterclockwise.
25
Shake the dirt from the filter and the mesh into a bin.
28
If necessary the filter and mesh can be rinsed, with cold
water, under a tap.
29
Air dry them for approximately 24 hours, to ensure it is
completely dry before re-using. Avoid direct sunlight
and extreme drying circumstances (e.q. hair-dryer).
27
Insert the cartridge filter back to the dust container
and turn it clockwise until the cartridge filter locks
completely.
24
Insert the protector mesh into its place by pushing it
onto the cartridge filter.
26
Close the dust container lid until it clicks.
22
Insert the dust container back into the cleaner by
pressing it down until it clicks.
Cartridge filter Menalux reference number: F110
INSTRUCTIONS FOR USE
AND ASSEMBLY
MAINTENANCE
35117_U1661 Lite_IFU_V4.indd 3
8/10/08 9:43:27 AM
