background image

2.Quick Start

 

 

11 

Capacitance Measurement   

Capacitance

 

Frequency/Period Measurement   

AC Signal

 

Temperature Measurement 

Temp Transducer

I

 

 

Data Record Function 

Data record function includes manual record and auto record. You can use any or both 

functions to record the data. The readings recorded in manual record or auto record will 

be saved into a same data table in the internal memory. The maximum number of 

readings is 1000. Once you have finished collecting data, you can view it in data table, 

and export it to a computer via RS232 port.   

Manual  record

:  Press  the  front  panel 

  key to save current reading  to  the data 

table of the internal memory.   

Auto record

: After setting number of points, sample interval, press the Start softkey to 

start recording. After recording, you can view the data saved in the data table of the 

internal memory. 

Manual Record   

1.

 

Collect data

: The instrument saves current reading in the data table of the internal 

memory each time the front panel 

  key is pressed. The 

  icon will show 

up on the top of the display. 

Note

:   

 

The measurement function can be switched during manual record.   

 

When the dual display is enabled, only the reading of main display function can be 

saved.   

2.

 

View the manual record

: Press the front panel 

  key, press the Manual softkey 

to display the data table. Press 

  keys to turn the page. (When the data table is 

Summary of Contents for 2203066


















Reviews: