Operation
Select the output voltage and change the low-voltage plug
(5)
only when the power
adapter is disconnected from the mains!
Observe the operating voltage of the appliance to be connected!
Also observe polarity. Incorrect pin assignment can damage both the end device
and product.
When connecting an appliance, make sure it is de-energized. A switched-on ap-
pliance can cause sparking when connecting the low-voltage plug, which in return
could damage both the product and the connected appliance.
The position of the voltage selection switch
(2)
determines the output voltage. There
are seven available output voltages printed around the voltage selection switch
(2)
.
The low-voltage plugs are marked with letters, dimensions and polarity symbols
-o)+
and
-(o+
.
1. Disconnect the product from the mains and any appliance it might be connected to.
2. Use the key
(4)
to turn the voltage selection switch until the arrow points to the voltage that
matches the input voltage of the load to be connected. The voltage selection switch should
noticeably and audibly lock into place.
3. Select one of the six low-voltage plugs featuring the exact dimensions matching the dimen-
sions of the appliance to be connected. Refer to the dimensions of the low-voltage plug
mentioned in chapter “Technical Data”.
4. Connect the low-voltage plug to the low-voltage socket observing the correct
-o)+
or
-(o+
polarity. The arrow located below the respective polarity marking must thereby be aligned
with the arrow of the low-voltage socket
(6)
. The low-voltage plug has been designed in a
way that it is quite hard to be removed.
5. Check if the appliance to be connected to the power adapter is switched off.
6. Then connect the other end of the low-voltage plug to the power supply jack of the appli-
ance.
7. Connect the power plug
(3)
to a common household wall socket. The LED power indica-
tor
(1)
on the top of the power adapter lights up. The product is now ready for use.
8. Switch on the appliance.
9. After use, switch off the appliance and unplug the power adapter from the wall socket. Only
then disconnect the low-voltage plug from the appliance.
Troubleshooting
Problem
Possible solution
The LED power indicator does
not light up.
No power supply voltage?
• Check the fuse of the wall socket.
• Check if the mains plug has been connected prop-
erly.
Is the power adapter overloaded?
• Disconnect all low-voltage loads from the device and
check the technical data.
The connected appliance does
not work.
Has the voltage been set correctly?
Has the polarity been selected properly? Does the LED
power indicator light up?
Is the power adapter overloaded?
• Disconnect all low-voltage loads from the device and
check the technical data.
The LED power indicator lights
up weakly and the connected
load does not work, even though
the correct voltage has been
selected.
Check if the voltage selection switch has properly
locked into place. If not, set it up correctly for it to lock
into place.
Maintenance and cleaning
• Never use aggressive or abrasive cleaning agents, rubbing alcohol or other chemical sol-
vents, as those can damage the housing or even affect the operation of the product.
• Besides occasional cleaning, the device is maintenance-free. There are no user-servicea-
ble parts inside the product. Therefore never open the product.
• Disconnect the product from the mains and any connected appliance before each cleaning.
•
To clean the product, a dry, soft and clean cloth is sufficient. You can easily remove dust
using a long-haired, soft and clean brush.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the house-
hold waste. At the end of its service life, dispose of the product in accordance with
applicable regulatory guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the envi
-
ronment.
Technical data
The efficiency data is in compliance with the ecodesign requirements set out in Annex II of
the EC regulation 2019/1782.
This symbol indicates that the product meets the energy efficiency requirements
for Class VI.
Input voltage .....................................................100 - 240 V/AC
Input AC frequency ...........................................50/60 Hz
Output voltage ..................................................3.0/4.5/5.0/6.0/7.5/9.0/12.0 V/DC
Output current ...................................................0.6 A
Output power .................................................... 1.8 W (3.0 V/DC) / 2.7 W (4.5 V/DC) /
3.0 W (5.0 V/DC) / 3.6 W (6.0 V/DC) /
4.5 W (7.5 V/DC) / 5.4 W (9.0 V/DC) /
7.2 W (12.0 V/DC)
Average active efficiency
..................................71.42 % (3.0 V/DC) / 80.12 % (12.0 V/DC)
Efficiency at low load (10%)
.............................61.63 % (3.0 V/DC) / 74.17 % (12.0 V/DC)
No load power consumption .............................0.10 W
Cable length ..................................................... 1.8 m
Protection class ................................................II
Operating conditions .........................................0 to +25 °C, 20 - 85 % RH (non-condensing)
Storage conditions ............................................-20 to +60 °C, 10 - 90 % RH (non-condensing)
Low-voltage plug (external Ø x internal Ø) ....... jack plug A: 2.5 mm
jack plug B: 3.5 mm
barrel plug D: 5.0 x 2.1 mm
barrel plug G: 5.5 x 2.5 mm
barrel plug H: 3.5 x 1.35 mm
barrel plug N: 5.5 x 1.5 mm
Dimensions (W x H x D) ...................................39 x 69 x 69 mm
Weight .............................................................. approx. 95 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represent the technical status at the time of printing.
Copyright 2020 by Conrad Electronic SE.
*2264183_v1_0620_02_jh_m_en_(1)
Model identifier:
ESPS-600-N
Commercial registration number:
HRB 3896
Manufacturer:
Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau
