background image

FAX version 911373_00(1) Page 5 of 9

5

Prepare lock side of door

for device and trim.

See “

Preparation Chart

” on page 3 for

drill, tap, and cut-out information

X

X

See trim instructions for pull side door

preparation. Line 

X

-

in trim instructions

is same as vertical device

 C 

.

L

9

7

Install trim (if using) and secure

device center case to door.

center

case

Trim

(optional)

1-1/2” Minimum clearance

(with end cap removed)

if device is too long for

door, see “

Cut Device

”

on page 9

B

8

Install mounting bracket

and end cap.

Secure

mounting bracket

and end cap

Mounting

bracket flush

Level 

device

Mark and prepare 2

mounting holes

See “

Preparation Chart

” on

page 3 for preparation

C

D

5

Cut tailpiece

if needed

1/2”

D

oor

surface

6

Tailpiece

Tailpiece guide

Rotate tailpiece

guide to match

tailpiece

If using an outside cylinder, check NL

drive screw and install tailpiece guide.

When installing trim that has a

functional lever, knob, or thumb piece

AND an outside cylinder to lock and

unlock the trim, remove NL drive screw

from back of device.

DO NOT remove NL drive screw for

the following application:

NL, EO, DT, TP-2, L-2, and K-2 trims or

with 98/99-2 (double cylinder).

With 

“BE”

 trim, device may need

rehanded. Look for instructions on

back of trim.

Note: When the NL

drive screw is left in

back of device, the

outside cylinder

will function only

as a Night Latch.

NL drive screw

Summary of Contents for 98










Reviews: