background image

8

Options are set by switches on the Chexit module. Before changing option settings, turn the Chexit off.
Changes in option settings take effect when the Chexit is turned on.

Seconds    Switch No. 1    Switch No. 2    Switch No. 3    Switch No. 4

0

2

4

6

8

10

12

14

16

18

20

22

24

26

28

 infinite

Rearm Time Switch Settings

off

on

off

on

off

on

off

on

off

on

off

on

off

on

off

on

off

off

on

on

off

off

on

on

off

off

on

on

off

off

on

on

off

off

off

off

on

on

on

on

off

off

off

off

on

on

on

on

off

off

off

off

off

off

off

off

on

on

on

on

on

on

on

on

Rearm Time Notes

1.

Set the rearm time a few seconds longer than
the door will be open so the door closes before
the Chexit arms.

2.

The Chexit is shipped from the factory with the
rearm time set to 10 seconds.

3.

When the rearm time is infinite, the Chexit
arms when the door position switch detects
that the door is closed.

4.

When the rearm time is infinite, you must open
and close the door after the Chexit is turned on.

5.

If a door position switch is used, the Chexit
arms 2.5 seconds after the door closes.

6.

If you are using a door position switch but you
want the full rearm time to expire before the
Chexit arms, call Technical Support at
1-877-671-7011. 

7.

For proper operation, the rearm time of each
ganged Chexit must differ by at least 2 seconds.

Location of Chexit

option switches

OPTIONS

Factory settings shown

8: Off
7: Off
6: Off
5: Off
4: Off
3: On
2: Off
1: On

Table 3. Chexit Options

Option

Rearm time

Nuisance delay

Nuisance alarm

Function

Switches No. 1 through 4

set amount of time you have to pass through door

after turning on key switch or using an external inhibit device (see table below)

If 

switch No. 5

 is on, the pushpad must be pressed 1 second to set off alarm

If 

switch No. 6

 is on, the Chexit horn sounds while pushpad is pressed during

nuisance delay; use in accordance with local code

Settings for Door No:

 ___

Self-test

Local fire alarm

If 

switch No. 7

 is on, the Chexit performs a self-test when turned on; this

switch must be off for normal operation

If 

switch No. 8

 is off, the Chexit internal horn sounds during a fire alarm

________ seconds

on                  off

on                  off

on                  off

on                  off

Summary of Contents for CX33A









Reviews: