VONROC AMIATA PH510AC, Original Instructions Manual

EN

7

WWW.VONROC.COM

holes.

4.   Insert the screws into the wall plugs and fasten 

the screws. Note: the screws should protrude 

approx. 0.5 cm from the wall plugs.

5.   Hang the heater on the screws.

6.   Check whether all 4 screws are hooked into 

the bracket and make sure that the device is 

attached securely.

7.   Tilt the device to the desired angle. The device 

can betilted downwards by 45°, as shown on 

figure E.

4. OPERATION

Switching on/off (Fig. A)

The heater can be turned on and off using the pull 

cord. Pull the cord of the pull switch (5) until the 

desired heating level appears on the heating level 

indicator (3):

•  Level 0 = switched off

•  Level 1 = 730W

•  Level 2 = 1460W

•  Level 3 = 2200W

To turn the heater off, pull the cord of the pull 

switch (5) to the 0 level position.

Tip over safety switch (Fig. A)

This heater is fitted with a tip-over safety switch. In 

the event that the heater falls over, the heater auto-

matically shuts off. Please note that when the heater 

is returned to its upright position, it does not resume 

its operating immediately. First switch it off (read 

‘switching on/off’), remove the plug from the socket 

and check the heater for damage. In case of damage 

or malfunctioning do not use but offer for checking / 

repair. If there is no damage, you can simply switch 

the heater on again (read ‘switching on/off’).

5. MAINTENANCE

 Always make sure that the machine is not 

connected to the mains electricity when you 

carry out any maintenance of the mechanism.

CAUTION: Risk of Electric Shock. DO NOT 

open or try to repair the heater yourself.

Clean the machine casings regularly with a soft 

cloth, preferably after each use. Make sure that the 

ventilation openings are free of dust and dirt. Re-

move very persistent dirt using a soft cloth  mois-

tened with soapsuds. Do not use any solvents such 

as gasoline, alcohol, ammonia, etc. Chemicals such 

as these will damage the synthetic components.

•   DO NOT use alcohol, gasoline, abrasive powders, 

furniture polish or rough brushes to clean the 

heater. This may cause damage or deterioration 

to the surface of the heater.

•  DO NOT immerse the heater in water.

•   Wait until the heater is completely dry before use.

ATTENTION:

1.   Always disconnect the heater from the electric-

ity supply and allow it to cool before attempting 

to clean it.

2.   If the heater has collected dust or dirt inside 

the unit or around the heating element, have to 

unit cleaned by a qualified service agent. Do not 

operate the heater in this condition.

3.   The only maintenance required is cleaning of 

the external surfaces of the heater.

4.   Do not touch the heating element with bare 

fingers, as residue from your hand could affect 

the life of the lamp. If it is accidentally touched, 

remove the finger marks with a soft cloth mois-

tened with mentholated spirit or alcohol.

5.   Do not attempt to repair or adjust any electrical 

or mechanical functions on this heater.

6.   The heater contains no user serviceable parts. 

Should the product suffer damage or break-

down, it must be returned to the manufacturer 

or its service agent.

7.   Damaged supply cords to be replaced by the 

manufacturer, service agent or similarly quali-

fied person in order to avoid hazard.

Storage

Store the heater in a cool, dry location when not in 

use to prevent dust and dirt build up. Use packag-

ing carton to store.

Trouble Shooting

If the heater will not operate, please check the 

following before seeking repair or service:

•    Check if the power cord is plugged into an 

electrical outlet, if not plug in.

•   Check if electricity to the main fuse is working.

•    Make certain the power switches are turned on 

If not, choose a setting.