10
EN
WWW.VONROC.COM
Lpa (Sound pressure level)
79+3 dB(A)
Lwa (Sound power level)
90+3 dB(A)
Vibration
1.177+1.5 m/s
2
Vibration level
The vibration emission level stated in this instruc-
tion manual has been measured in accordance
with a standardised test given in EN 60745; it may
be used to compare one tool with another and as
a preliminary assessment of exposure to vibration
when using the tool for the applications mentioned.
- using the tool for different applications, or with
different or poorly maintainted accessories, may
significantly increase the exposure level.
- the times when the tool is switched off or when
it is running but not actually doing the job, may
significantly reduce the exposure level.
Protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work patterns.
DESCRIPTION
The numbers in the following text refer to the
pictures on page 2-4
1. Collet chuck
2. Spindle lock
3. On/off button and speed adjustment button
4. Speed indication lights
5. Charger indication light
6. Charger cable
3. ASSEMBLY
Always make sure the machine is turned off
before mounting an accessory.
Warning! Change accessories by inserting
an accessory into the collet (or chuck) as far
possible to minimize run out and unbalance.
Assembly of accessories
(
Fig. B)
Press the spindle lock button (2) and hold it.
Unscrew the collet chuck (1) by hand. Put the
accessory in its place. Press the spindle lock button
(2) when fastening the collet chuck (1).
Do not press the spindle lock button while
the motor is running.
4. OPERATION
Switch on the machine by pressing the on/off
button (3). By pressing the on/off button (3) a
second time, the machine will adjust to speed 2,
press for the third time and the machine will adjust
to speed 3. By pressing the on/off button (3) for a
fourth time, the machine switches off. Do not put
the machine down when the motor is still running.
Do not place the machine on a dusty surface. Dust
particles may enter the mechanism.
Too high a load at a low speed of the
Combitool can burn out the engine.
The battery must be charged before first use.
Charging the device (with the charger)
• Plug the charger cable (6) (included) into an
adapter (not included).
• Plug the charger cable (6) into the machine. (fig. J)
• Plug the charger plug into an electrical outlet
and wait for a while. The charger indication light
(5) will lighten up and show the charging status.
LED
Charger status
Red
Battery charging in progress
Green
Battery charging finished, battery fully charged
• After the battery is fully charged remove the
charger plug from the outlet and remove the
small plug from the device.
Holding and guiding the tool (Fig. C)
• For precision work (engraving): pencil grip (C1)
• For rough work (grinding): paring knife hand grip
(C2)
• When you need to keep the tool parallel to the
work surface (e.g. using a cut-off wheel): 2 hand
golf grip (C3)
Optimal use of the combi tool and its accessories
(Fig. A)
For optimal use of the accessories use the correct
speed. You can refer to the overview “Recommended
speed setting” below to determine the correct
speed, based on the material being worked on and
the type of accessory being used. This overview
enables you to select both correct accessory and
the optimum speed.
Summary of Contents for CT502DCl
