4
EN
WWW.VONROC.COM
wear eye protection.
Protective equipment
such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c)
Prevent unintentional starting. Ensure the
switch is in the offposition before connecting
to power source and/or battery pack, picking up
or carrying the tool.
Carrying power tools with
your finger on the switch or energising power
tools that have the switch on invites accidents.
d)
Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
e)
Do not overreach. Keep proper footing and
balance at all times.
This enables better control
of the power tool in unexpected situations.
f)
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts.
Loose clothes, jewel-
lery or long hair can be caught in moving parts.
g)
If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of
dust collection can reduce dust related hazards.
h)
Do not let familiarity gained from frequent use
of tools allow you to become complacent and ig
nore tool safety principles.
A careless action can
cause severe injury within a fraction of a second.
4) Power tool use and care
a)
Do not force the power tool. Use the correct
power tool for your application.
The correct
power tool will do the job better and safer at the
rate for which it was designed.
b)
Do not use the power tool if the switch does not
turn it on and off.
Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
c
) Disconnect the plug from the power source
and/or the battery pack from the power tool be
fore making any adjustments, changing acces
sories, or storing power tools.
Such preventive
safety measures reduce the risk of starting the
power tool accidentally.
d)
Store idle power tools out of the reach of child
ren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool.
Power tools are dangerous in
the hands of untrained users.
e)
Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use.
Many accidents
are caused by poorly maintained power tools.
f)
Keep cutting tools sharp and clean.
Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g)
Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed.
Use of the power tool
for operations different from those intended
could result in a hazardous situation.
h)
Keep handles and grasping surfaces dry, clean
and free from oil and grease.
Slippery handles and
grasping surfaces do not allow for safe handling
and control of the tool in unexpected situations.
5) Service
a)
Have your power tool serviced by a qualified
repair person using only identical replacement
parts.
This will ensure that the safety of the
power tool is maintained.
ADDITIONAL SAFETY WARNINGS FOR
IMPACT DRILLS
This machine is suitable for light work.
Do not overload the machine.
a)
Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
b)
Use auxiliary handle(s), if supplied with the
tool.
Loss of control can cause personal injury.
c)
Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord.
Cutting accessory contacting a “live” wire
may make exposed metal parts of the power tool
“live” and could give the operator an electric shock.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the power supply
corre sponds to the voltage on the rating plate
.
Summary of Contents for ID502AC
Page 2: ...WWW VONROC COM 2 A B 2 4 7 6 5 1 3 8 2 11 10...
Page 74: ...74...
