6
EN
WWW.VONROC.COM
temperature range specified in the instructions.
Charging improperly or at temperatures outside
the specified range may damage the battery and
increase the risk of fire.
6) Service
a)
Have your power tool serviced by a qualified
repair person using only identical replacement
parts.
This will ensure that the safety of the
power tool is maintained.
b)
Never service damaged battery packs.
Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
ADDITIONAL SAFETY INSTRUCTIONS
• Do not use oversized sanding sheets, but follow
the manufacturer’s specifications for the size of
sanding sheets. Sanding sheets which project
over the sanding pad may cause injuries as well
as block and rip the sanding sheets or cause a
kickback.
• It is not recommended to sand lead paint. Lead
paint should be removed by a specialist only.
• Do not work on materials which release
hazardous substances (e.g. asbestos). Take
precautions if hazardous, combustible or
explosive dust is likely to occur. Wear protective
dust mask. Use dust extraction system.
• Do not work materials containing asbestos.
Asbestos is considered carcinogenic.
• Do not use the machine for sanding magnesium
workpieces.
• Wear safety goggles. Wear hearing protection.
If necessary, use other protective means, such
as safety gloves, safety shoes, etc.
• Hold the machine by the insulated gripping
surfaces where the accessory may contact
hidden wiring or the mains cable. If the
accessory contacts a ‚live‘ wire, the exposed
metal parts of the machine can also become
‚live‘. Risk of electric shock.
• Be very careful when sanding painted surfaces.
• Before use, remove all nails and other metal
objects from the workpiece.
• Make sure that the workpiece is properly
supported or fixed.
• Only use sanding paper that is suitable for use
with the machine.
• Only use sanding paper with the correct
dimensions. Make sure that the sanding paper
is properly mounted.
• Inspect the sanding paper before each use.
Do not use sanding paper that is worn because
of prolonged use.
• Never put the machine down on a table or a
workbench before it has been switched off.
SAFETY WARNINGS FOR BATTERY
a)
Do not open the battery
. Danger of short-
circuiting.
b)
Protect the battery against heat, e. g., against
continuous intense sunlight, fire, water, and
moisture
. Danger of explosion.
c)
In case of damage and improper use of the bat
tery, vapours may be emitted. Ventilate the area
and seek medical help in case of complaints
.
The vapours can irritate the respiratory system.
d)
Use the battery only in conjunction with your
Vonroc product
. This measure alone protects
the battery against dangerous overload.
e)
The battery can be damaged by pointed objects
such as nails or screwdrivers or by force
applied externally
. An internal short circuit can
occur and the battery can burn, smoke, explode
or overheat.
SAFETY WARNINGS FOR CHARGER
Intended use
Charge only CD801AA and CD803AA type recharge-
able Battery packs with the charger. Other types
of batteries may burst causing personal injury and
damage.
a) The appliance is not to be used by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of expe
rience and knowledge, unless they have been
given supervision or instruction.
b) Children being supervised not to play with the
appliance.
c) Do not recharging nonrechargeable batteries!
d) During charging, batteries must be placed in
the well ventilated area!
Electrical safety
Always check that the voltage of the power
supply corresponds to the voltage on the
rating plate.
• Do not use the machine if the mains cable or
the mains plug is damaged.
• Only use extension cables that are suitable for
the power rating of the machine with a minimum
Summary of Contents for PS502DC
