6
EN
WWW.VONROC.COM
temperature range specified in the instructions.
Charging improperly or at temperatures outside
the specified range may damage the battery and
increase the risk of fire.
6) Service
a)
Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the
power tool is maintained.
b) Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SAFETY WARNINGS FOR STAPLE GUN
a) Always assume that the tool contains fasteners.
Careless handling of the tool can result in unex-
pected firing of fasteners and personal injury.
b) Do not point the tool towards yourself or
anyone nearby. Unexpected triggering will
discharge the fastener causing an injury.
c)
Do not actuate the tool unless the tool is placed
firmly against the workpiece. If the tool is not
in contact with the workpiece, the fastener may
be deflected away from your target.
d) Disconnect the tool from the power source
when the fastener jams in the tool. While
removing a jammed fastener, the tacker may be
accidentally activated if it is plugged in.
e)
Use caution while removing a jammed fastener.
The mechanism may be under compression and
the fastener may be forcefully discharged while
attempting to free a jammed condition.
f)
Do not use this tool for fastening electrical
cables. It is not designed for electric cable
installation and may damage the insulation of
electric cables thereby causing electric shock
or fire hazards.
SAFETY WARNINGS FOR BATTERY
a)
Do not open the battery. Danger of short-
circuiting.
b) Protect the battery against heat, e. g., against
continuous intense sunlight, fire, water, and
moisture. Danger of explosion.
c)
In case of damage and improper use of the bat
tery, vapours may be emitted. Ventilate the area
and seek medical help in case of complaints.
The vapours can irritate the respiratory system.
d) Use the battery only in conjunction with your
Vonroc product. This measure alone protects
the battery against dangerous overload.
e)
The battery can be damaged by pointed objects
such as nails or screwdrivers or by force
applied externally. An internal short circuit can
occur and the battery can burn, smoke, explode
or overheat.
SAFETY WARNINGS FOR CHARGER
Intended use
Charge only CD801AA and CD803AA type recharge-
able Battery packs with the charger. Other types
of batteries may burst causing personal injury and
damage.
a) The appliance is not to be used by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of expe
rience and knowledge, unless they have been
given supervision or instruction.
b) Children being supervised not to play with the
appliance.
c) Do not recharging nonrechargeable batteries!
d) During charging, batteries must be placed in
the well ventilated area!
Electrical safety
Always check that the voltage of the power
supply corresponds to the voltage on the
rating plate.
• Do not use the machine if the mains cable or
the mains plug is damaged.
• Only use extension cables that are suitable for
the power rating of the machine with a minimum
thickness of 1.5 mm
2
. If you use an extension
cable reel, always fully unroll the cable.
2. MACHINE INFORMATION
Intended use
This power tool is intended for indoor domestic
use. This tool may be used for fastening suitable
cardboard, insulation material, textile, leather,
wood and similar non-brittle materials to a wooden
surface. This tool is not suitable for fastening
electrical cables, or wall or ceiling panelling.
The tool is not intended for artisanal, commercial,
professional and / or industrial use.
NOTE: Some timbers (such as very dry hardwood)
may require shorter staples to fully drive in.
Summary of Contents for S2 SG503DC
Page 2: ...WWW VONROC COM 2 A B C 6 8 10 7 2 11 4 5 1 9 3 2 1 2 2 14 13 12 15 15...
Page 81: ...81...
Page 82: ...82...
