background image

The turbine should not be exposed to excessive water pressure and/or water flow velocity, which

must not exceed the safe maximum value of 11 m/s.

The user must read and follow this and the inverter's manual before starting the installation.

The user must follow all the installation and connection instructions provided in the inverter's

user's manual.

The following items are not included in your purchase: 

1. intake screen (-s)
2. pipe flange
3. pipes

4. power cables. 

GETTING READY

Upon receipt of the turbine, unless purchased from and installed by the authorized Vortex Hydrokinetics

LLC distributor/dealer, make sure that all boxes are not damaged. 

Check part conformity with the delivery list and ensure there are no damaged or defective parts; should

there be any, please inform Vortex Hydrokinetics LLC immediately.

The parts are manufactured by their respective manufacturers for Vortex Hydrokinetics LLC. Do not

contact these manufacturers directly in an attempt to resolve any issues as it could void our limited
lifetime warranty to you unless specifically authorized by Vortex Hydrokinetics LLC.

RECYCLE! Any packing materials should be disposed of via correct waste disposal methods. Do

not discard waste materials into the environment.

The following parts are normally shipped in separate boxes:

Assembled turbine

Bridge rectifier

Inverter

Vortex Hydrokinetics LLC © 2019 

SETUR-M User's Manual -  Rev. 2M-A

Page 13 of 24

Summary of Contents for SETUR-L

























Reviews: