BASE
TIMER
PIR
PULL CORD
T HCS
MHC
MODELLI
Punto Vortice BASE NORMALE / AUTOMATICO
Il prodotto è azionato dandogli tensione attraverso
l’interruttore di comando.
Nella versione automatica le alette di chiusura si aprono
dopo qualche secondo dall’accensione.
Punto Vortice TIMER NORMALE / AUTOMATICO
Il prodotto è dotato di timer tarato per un tempo minimo di 3
minuti. È possibile variare detta entità nell’arco di tempo da
3 a 20 minuti, agendo sul trimmer (vedi fig. 13).
L’apparecchio si avvia automaticamente alcuni secondi dopo
l’accensione della luce e continua a funzionare per il tempo
prefissato dopo lo spegnimento della luce stessa.
Punto Vortice PIR NORMALE / AUTOMATICO
Il prodotto è dotato di un circuito elettronico con un sensore
che ne attiva il funzionamento per un tempo prefissato,
regolabile da 3 a 20 min. (vedi fig. 16), quando rileva la
presenza di una persona nel proprio raggio d’azione.
Punto Vortice Pull Cord NORMALE / AUTOMATICO
Il prodotto è dotato di un interruttore manuale a funicella
che, tirata, attiva/disattiva il funzionamento dell’apparecchio.
Punto Vortice T HCS NORMALE / AUTOMATICO
Il prodotto è dotato di un circuito rilevatore d’umidità pre
impostato che attiva il funzionamento dell’apparecchio
quando la percentuale d’umidità supera il 65%. Il circuito è
inoltre dotato di timer regolabile da 3 a 20 min. agendo sul
trimmer (vedi fig. 14). L’apparecchio si avvia
automaticamente alcuni secondi dopo l’accensione della luce
e continua a funzionare per il tempo prefissato dopo lo
spegnimento della luce stessa.
Punto Vortice MHC NORMALE / AUTOMATICO
Il prodotto è dotato di un sistema a microprocessore MHC per
il controllo dell’umidità. È programmato in modo da attivarsi
quando la temperatura ambiente è di 20° C e la percentuale
d’umidità supera il 65%. Il microprocessore controlla in modo
permanente l’ambiente rilevando i valori della temperatura e
dell’umidità e calcola la temperatura media su una durata di
48 ore. Questo sistema permette al microprocessore di
fissare automaticamente il punto d’arresto ottimale. Il circuito
è inoltre dotato di timer regolabile da 3 a 20 min. agendo sul
trimmer (vedi fig. 15).
Punto Vortice 12 VOLT NORMALE / AUTOMATICO
ATTENZIONE: ALIMENTARE I PRODOTTI SOLO CON I
GRUPPI 12V VORTICE
I prodotti sono costruiti in classe III e cioè la sicurezza
elettrica si basa sull’alimentazione con bassissima tensione
di sicurezza che è garantita solamente se i prodotti sono
alimentati con i gruppi VORTICE GA 12V - 12V T - 12V P -
12V MHC - 12V HCS.
DIAMETRO
BASE
TIMER
PIR
PULL CORD
T HCS
MHC
12 V
S
T
A
N
D
A
R
D
NORMALE
AUTOMATICO
∅
100
•
•
•
•
•
•
•
∅
0
90
•
•
∅
120
•
•
•
•
•
•
–
∅
150
•
•
•
•
•
•
–
∅
100
•
•
•
•
•
•
•
∅
120
•
•
•
•
•
•
–
∅
150
•
•
•
•
•
•
–
DIAMETRO
L
O
N
G
L
I
F
E
NORMALE
AUTOMATICO
∅
100
•
•
•
•
•
•
∅
120
•
•
•
•
•
•
∅
150
•
•
•
•
•
•
∅
100
•
•
•
•
•
•
∅
120
•
•
•
•
•
•
∅
150
•
•
•
•
•
•
Questa è la gamma completa dei Punto Vortice. Non tutte le versioni sono disponibili in tutte le nazioni.
9
Summary of Contents for 8010300112121
