background image

4

PRO9556Z Owners REV.D 

 Entering the Vehicle while it is Running via Remote Vehicle Start 

(Optional)

1.  Unlock the vehicle’s doors.
2. 

Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL!

3.  Insert the key into the ignition switch and turn to the ON or RUN 

position.

Press the brake pedal. The remote vehicle starter will disengage and the 

vehicle will operate normally.

NOTE: 

This feature may not be available on all vehicle makes/models. In 

some vehicle applications the remote start will shut down upon entering the 

vehicle and the engine will stop running. For these applications it will be 

necessary to restart the vehicle normally. Refer to installing dealer for details.

 System Arm 

To Arm and lock the vehicle doors press and release the   button. The LED 

on the antenna will flash one (1) time while armed.

 System Disarm 

To Disarm and unlock the vehicle doors press and release the   button.

 System Override 

To disarm the system without the use of the remote control locate the valet 

override button on the windshield mounted antenna.

1.  Enter the vehicle.
2.  Turn the vehicle’s ignition to the ON position.
3.  Press and release the valet button one (1) time.

The system is now disarmed and will remain disarmed until the   button is 

pressed.

 Valet Mode 

Valet mode allows the user to Lock or Unlock the vehicle without Arming the 

security system. To enter or exit valet mode:

1.  Turn the vehicle ignition to the ON position.
2. 

Press and hold the valet button for five (5) seconds. The LED on the

 

antenna will turn on solid.

Using Your Security System 

(Optional)

Summary of Contents for Pursuit PRO9556Z









Reviews: