Voxx Pursuit PRO9051E Install Manual Download

Page: 16 / 16

128-9353

16 of 16

Page 16

PRO9051E

To Mating Connector

Push Button

LED Transceiver

Blue (LED -)

Grey (Valet)

Black (-)

Green (RX)

Red (+)

Connect Data Module

DBI Protocol

Wire Side View Of Connector

1 Blue (Ign 1)

2 Red/White (+ 12VDC Relays Ign 1 & Ign 2)

3 Green (Ign 2)

4 Purple (Accessory)

5 Red (+ 12VDC Relays ACC & Start)

6 Yellow (Starter)

1 Green/Orange (Tach Input)

3 Black/Blue (- Pulse Before Start Output)

4 Black/LT.Green (- Pulse After Start Output)

5 LT. Blue (Ground Out While Running)

6 Green/Yellow (Glow Plug Input)

7 Brown (+ Inhibit Wire)

8 Gray (- Negative Inhibit Wire)

9 Black/Red (- Pulse After Shut Down Output)

10 Black/Yellow (- Pulse During Crank Output)

2 Empty Cavity No Connection

Yellow/Black (To controlling Alarm’s Ign Input)

White (Parking Light Relay Output)

Black (Chassis Ground)

White/Red (Parking Light Relay Input

)

2014 Voxx Electronics Corporation, 150 Marcus Blvd. Hauppauge, NY 11788

128-9353

For technical support go to www.pursuitcarsecurity.com or call 1 800 225 6074

Summary of Contents for Pursuit PRO9051E

















Search results

Summary of Contents for Pursuit PRO9051E

Reviews:

Related manuals for Pursuit PRO9051E

Brands by name

Popular brands

Voxx Pursuit PRO9051E, Install Manual

Search results

Summary of Contents for Pursuit PRO9051E

Reviews:

Related manuals for Pursuit PRO9051E

Brands by name

Popular brands