VPI Scout/JMW-9T Setup And Instruction Manual Download

Page: 3 / 10

Introduction

The Scout turntable is a precision instrument featuring the new
Tapered arm tube version of the JMW-9 tonearm. It has been

thoroughly tested and run for at least 4 hours. The speed accuracy,
wow, flutter, and rumble have been checked, and this unit meets all of
our specifications.

Minimum Specifications



Wow and flutter



Less than .02%.



Rumble



Greater than 78db down.



Speed accuracy



Within .1%.



Total weight



32 pounds.



Platter run out



+/- .001 inch.

Product Specifications



600 RPM AC synchronous drive motor.



Drive belt custom-made for VPI.



Aluminum cone feet with stainless steel ball bearings on the

bottoms.



Solid acrylic platter with bronze bushings and Peek thrust surface.



Platter sits on 60 Rockwell-hardened shaft and chrome-hardened

ball bearing.

Complete and return the warranty card. The

warranty does not take effect until the
warranty card is returned.

Summary of Contents for Scout/JMW-9T











Search results

Summary of Contents for Scout/JMW-9T

Reviews:

Related manuals for Scout/JMW-9T

Brands by name

Popular brands

VPI Scout/JMW-9T, Setup And Instruction Manual

Search results

Summary of Contents for Scout/JMW-9T

Reviews:

Related manuals for Scout/JMW-9T

Brands by name

Popular brands