background image

PIPER PA-18

Radio control model
R/C Flugmodell

MONTAGEANLEITUNG

Designed for brushless electric motors

 

(.46-.52 class glow conversion optional)

Entwickelt für Brushless Elektro Motoren 

(7,5 -8,5cc Glühzündermotor Einbau möglich)

INSTRUCTION MANUAL

SPECIFICATIONS

Wingspan                                          63.7in.
Length                                              49.2 in.
Electric Motor                      (See next page)
Glow Engine        .46 2Stroke / .52 4-Stroke
Radio                     5 Channel / 4 -5 Servos

WARNING!

 This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! 

Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,

die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

TECHNISCHE DATEN

Spannweite                                    1620mm
Lange                                             1250mm
Elektroantrieb             (siehe nächste Seite)
Verbrennerantrieb       7.5cc 2-T / 8.5cc 4-T
Fernsteuerung           5 Kanal / 4 -5 Servos

SUPER CUB

Floats available as an option! (No. C4682)
Schwimmer als Sonderzubehör erhältlich! (Best.Nr.C4682)

Summary of Contents for L4A GRASSHOPPER

















Reviews: